Comparison
Best Estimating Software for Roofing Contractors:Aerial Measurement, Low-Slope Takeoff and Report Prices for Eight Tools
Best estimating software for roofing contractors compared: iRoofing, Hover, RoofLink, The EDGE, STACK, Square Takeoff, EagleView and FieldRanger on price.
The best estimating software for roofing contractors splits by roof. Residential reroofers pricing at the house suit iRoofing, Hover or RoofLink; commercial roofers bidding low-slope work from plans suit The EDGE or STACK, with Square Takeoff for plan takeoff without a contract; EagleView supplies measurement reports to either; and FieldRanger suits roofers whose estimates and crews run from HubSpot deals.
A steep-slope estimate starts from squares, pitch and facets measured from an aerial image or a phone scan, and ends in shingles, underlayment, ridge and waste. A low-slope estimate starts from plans and ends in membrane, tapered insulation to the drains, fasteners and flashing at every parapet. The two need different measurements, and the vendors below state which roof each is built for. The roofing contractor software page shows how FieldRanger runs the job after the estimate, and head-to-head pages sit in the field service software comparisons hub.
The comparison defines the roofing measurement terms, states the criteria and sets eight tools side by side by pricing unit. Entries follow in four groups: residential measure-and-price tools, commercial low-slope takeoff, a report provider and FieldRanger. A capability table, a year-one cost for 100 residential roofs and a bid test close it before the questions. Each vendor fact was read on that vendor's own page with a plain request on 13 November 2026; review-site ratings play no part. FieldRanger publishes this comparison and makes one of the products in it.
Roof measurement terms: squares, pitch, facets, tapered insulation and reports
A square is 100 square feet of roof surface. Pitch is the rise in inches over 12 inches of run, and it converts a flat footprint into true surface area. A facet is one plane of the roof; a gable roof has two, and a cut-up custom home can have twenty. A waste factor adds material for cuts at hips, valleys and rakes.
Low-slope roofs are measured differently. The membrane covers the field, tapered insulation boards build slope toward drains or scuppers, crickets divert water around curbs, and flashing runs up every parapet and penetration. Fastener counts follow the insulation and the wind zone. A measurement report is a document a provider produces from aerial imagery, sold per roof; a takeoff is the estimator's own measurement from plans or images inside the estimating tool. Insurance claim estimates in Xactimate and the CRMs that track them are compared in best roofing software.
Selection criteria for roofing estimating tools
- Measurement source: aerial imagery, phone scan, plans, or a purchased report.
- Steep-slope output: squares, pitch, facets, and waste by material.
- Low-slope output: membrane, tapered insulation layout, fasteners and flashing.
- Price per measurement or report, and whether the subscription includes any.
- Material catalogs and proposals with options, sent for signature.
- Users included, setup fees and contract term.
- Supplier ordering, accounting and CRM connections named on the vendor's page.
- Published price and trial, dated.
Eight roofing estimating tools by pricing unit
| Tool | Pricing unit | Published entry price | Users, setup and trial |
|---|---|---|---|
| iRoofing | Flat subscription | $149 a month, or $124 a month billed $1,488 a year | 3 users; $75 of imagery credit a month |
| Hover | Per project, with optional annual plans | Roof measurement from $29 a project on Starter, $9 on Pro; Pro $999 a year | First 3 projects free |
| RoofLink | Per user | $120 a user a month, the price counter's target value | One-time $1,500 setup fee |
| Square Takeoff | Flat subscription per license | $249 a month, or $1,699 a year | 14-day trial |
| STACK | Per user | Premium $299 a user a month billed annually | 12-month term; free version |
| The EDGE | Not published | Demo | Not stated |
| EagleView | Per report, by tier | Premium commercial report $89.50 at Bronze | Account required to order |
| FieldRanger | Per technician | See [pricing](/pricing) | 14 days, no card |
The units decide the bill. iRoofing and RoofLink include measurement in the subscription, while Hover and EagleView charge per roof, so the comparison turns on how many roofs a contractor measures a year.
Residential estimating at the house
The iRoofing subscription: three users, DIY measurement and an imagery credit
Best for: small residential reroofers who measure from aerial imagery, show the homeowner a visualized roof and sign the contract in one visit. Price: $149 a month billed monthly, $124 a month billed $1,488 a year, or $107 a month billed $2,576 for two years. Every plan includes 3 users, unlimited DIY roof measurements and proposals, and a $75 monthly HD imagery credit of 150 credits (iroofing.org/pricing, checked 13 November 2026).
Strengths: plans include AI roof visualizations, a pitch book, a pricing catalog, multi-option proposals, digital contracts, distributor ordering, job tracking and appointment scheduling. A perimeter report costs $10 without a subscription, with 20% off it for subscribers, and the page states no setup fees. Falls short on: the device table lists the instant estimate, presentations, contracts and material orders under the tablet only, while the desktop and phone lists show measurements and visualizations. The pricing page describes residential selling and names no low-slope tools, and no HubSpot connection is named.
Hover: phone-scan 3D models priced by facets
Best for: residential contractors who measure from photos taken on a phone and price roof, siding and gutters from one 3D model. Price: Starter is pay per project with the first 3 projects free; Pro costs $999 a year and takes $20 off every project; Business costs $2,999 a year for a flat rate per project type (hover.to/pricing, checked 13 November 2026).
Strengths: a roof-only measurement costs $29, $49 or $69 on Starter for up to 4, 5 to 8, or 9 or more facets, $9, $29 or $49 on Pro, and $39 flat on Business. Blueprint roof measurements from plans cost $49 to $149 on Starter and $99 flat on Business. Every plan sends data to Verisk or Cotality for insurance estimates, and Pro adds CRM and other integrations; Business runs up to 10 branches with single sign-on. Falls short on: the feature grid marks production-ready estimates, labor and fees, and sales estimates as not included on Starter, so pricing a roof in Hover starts at $999 a year. A custom product list of the company's own SKUs appears only on Enterprise. The Business flat rate costs more than Starter on a simple roof, the structure sizes are written for houses and garages, and the page names no CRM.
RoofLink: measurement, estimate and production for one per-user price
Best for: residential and insurance roofers whose reps measure, estimate, order and collect from one app without per-measurement charges. Price: $120 a user a month plus a one-time $1,500 setup fee, with "no per-measurement costs" (rooflink.com/pricing, checked 13 November 2026). The animated counter on that page starts at $400 and settles on $120; the static figure in the page code is $400 and the counter's target value is $120, which matches the RoofLink Pro price on SalesRabbit's pricing page.
Strengths: the homepage describes canvassing territories, storm tracking, a full roof measurement in minutes, an estimate from that measurement with the margin shown, approval, ordering, installation and payment on retail or insurance jobs. It integrates with SalesRabbit, SRS, QuickBooks, Stripe, Hover, EagleView, CompanyCam and Zapier. SalesRabbit's page lists inspections, a product library and QuickBooks financing for RoofLink Pro. Falls short on: the $1,500 setup fee, and no trial is stated; the page offers a demo. The revenue figure on the pricing page is marked as based on internal user data, which is not evidence. No HubSpot connection is named.
Roofr and RoofSnap, which pair measurement reports with estimates at published prices, are covered in best roofing software alongside the roofing CRMs.
Commercial roofing estimating software for low-slope takeoff
The EDGE: tapered insulation, standing seam and poured deck modules
Best for: commercial roofing contractors who bid membrane, metal and lightweight concrete roofs from plans and need fastener counts and tapered layouts without waiting for a supplier. Price: not published; the roofing page offers a demo (checked 13 November 2026).
Strengths: the Tapered Insulation module produces the material list and fastener counts, and the Standing Seam module produces materials and a cut list for the field. The Poured Deck module measures lightweight concrete: the estimator draws drains or scuppers and the slope direction, and it lists every board and the concrete required. The system is cloud-based, and the page names Smart Labor and a one-click update of a whole project. The homepage adds the ability to calculate fastener lengths and EDGE On Site for tracking production against the estimate. Falls short on: no price or trial, and the pages name no aerial measurement or CRM, so a residential reroof business gains little from it.
STACK: flat and pitched roofs from plans or aerial images
Best for: commercial roofers with several estimators who measure from PDF plans and aerial images in the cloud. Price: Premium is $299 a user a month billed annually or $349 paid monthly, and Pro $349 or $399, on a 12-month term (STACK takeoff and estimate pricing, checked 13 November 2026).
Strengths: the roofing page covers pitched and flat roofs of any material, measurement from PDF, TIFF or the aerial imagery library, and a library of roofing items and systems with labor, waste, taxes and margin. Its FAQ names flat, low-slope, metal and shingle roofs. The plan grid marks estimating with items and assemblies on Premium and Pro, though the Pro card lists it as a Pro addition, and Pro adds worksheet-style estimating and native proposals. Falls short on: the Aerial Image Takeoff add-on, which completes takeoffs including pitch from aerial images, requires Premium and has no printed price. The page names no tapered insulation or fastener calculation, and its embedded product data lists Premium at $249 and Pro at $299, against $299 and $349 on the page.
Square Takeoff: a roof area tool on a $249 monthly plan
Best for: small commercial and residential roofers who want plan takeoff with a roof tool set and no contract. Price: $249 a month month to month, $599 a quarter or $1,699 a year, with every feature on each plan and a 14-day trial (squaretakeoff.com/pricing, checked 13 November 2026).
Strengths: the roof area tool measures hips, valleys, beams, gable ends and sheathing, and estimates break down material, labor and equipment with an editable parts catalog. Blueprint overlay catches revised sheets, and reports export to Excel. Falls short on: the tool set is described for pitched-roof geometry, with no tapered insulation or membrane layout named, and a second license is priced by phone.
Measurement reports for commercial and residential bids: EagleView
Best for: roofers who buy a measured report for each roof, commercial buildings included, and price it in their own estimating tool. Price: per report at Bronze, Silver and Gold tiers, with Platinum priced by call. A Premium commercial report costs $89.50, $84.25 or $79, and a Bid Perfect commercial report $49 at Bronze, Silver and Gold (eagleview.com/pricing, checked 13 November 2026).
Strengths: residential Premium reports run from $32.75 for a small roof of 20 squares to $87 for one over 40 squares at Bronze. Commercial gutter reports cost $23.25 and commercial walls reports $221.25. The page states that reduced Silver, Gold and Platinum pricing can come through an integration partner, a distributor or purchase volume, and RoofLink names EagleView among its integrations. Falls short on: EagleView sells the measurement, not the estimate, so the price, the proposal and the job sit in another tool, and the per-report cost repeats on every bid.
Roofing estimates on HubSpot deals: FieldRanger
Best for: residential and light commercial roofers whose leads, inspections and estimates move through a HubSpot pipeline worked by sales reps. Price: per technician, on the FieldRanger pricing page; Start free trial runs 14 days with no card.
Strengths: an estimate is built from the HubSpot deal or contact record, or in FieldRanger and kept tied to the deal, with the estimating software described on the features page, and estimates go out for signature through PandaDoc. A won deal becomes a job with its context carried over. Photos taken on the roof sync to the customer's HubSpot record, the customer signs on site, and materials used are logged to the job for costing. The invoice is generated from the completed work order, payment is taken through Stripe, and invoices and payments sync with QuickBooks. The HubSpot field service page sets out the records.
Falls short on: FieldRanger does not measure roofs or order aerial reports, so squares and pitch come from iRoofing, Hover, EagleView or a takeoff tool. There is no weather feed for storm tracking or install days. A tear-off and reroof over several days is one job per day, because multi-day jobs are not built. Progress billing and retainage are not built, so a commercial reroof billed by schedule of values runs elsewhere. A contractor bidding low-slope work from plans is better served by The EDGE or STACK.
Measurement source, low-slope output and proposals by tool
| Capability | Where it is stated |
|---|---|
| Measurement source | iRoofing, aerial imagery; Hover, phone photos and blueprints; RoofLink, in-app measurement; STACK, plans and aerial images; Square Takeoff and The EDGE, plans; EagleView, purchased reports; FieldRanger, none |
| Low-slope output | The EDGE, tapered insulation, standing seam and poured deck; STACK, flat and low-slope roofs named; Square Takeoff, iRoofing, Hover and RoofLink, not stated |
| Measurement cost | iRoofing and RoofLink, included; Hover, per project; EagleView, per report; STACK, Square Takeoff and The EDGE, the estimator's own takeoff; FieldRanger, not applicable |
| Proposal and signature | iRoofing, proposals and digital contracts; Hover Pro, estimates, comparisons and agreements; RoofLink, estimate and approval; STACK Pro, native proposals; FieldRanger, estimates through PandaDoc |
| Named CRM or accounting | RoofLink, SalesRabbit and QuickBooks; Hover Pro, unnamed CRM sync; iRoofing, Square Takeoff, The EDGE and EagleView, none named; FieldRanger, HubSpot and QuickBooks |
The low-slope row is the narrow one. Only The EDGE names tapered insulation and fastener counts, and STACK names flat and low-slope roofs without a tapered layout, so a commercial estimator should test both on the same set of plans.
Year-one cost for 100 residential roofs
The sample prices one estimator measuring and pricing 100 average houses of 5 to 8 facets in a year. It is arithmetic on list prices, not a quote; ordered reports, taxes and hardware are excluded.
| Tool and plan | Basis | Year one |
|---|---|---|
| iRoofing, 12 months | Flat; unlimited DIY measurement; 3 users | $1,488 |
| RoofLink | 1 user at $120 a month, plus $1,500 setup | $2,940 |
| Hover Pro | $999 plus 100 roof measurements at $29 | $3,899 |
| Hover Starter | 100 roof measurements at $49; estimates limited | $4,900 |
| EagleView Premium, medium roof, Bronze | 100 reports at $60; estimate tool not included | $6,000 |
| Hover Business | $2,999 plus 100 measurements at $39 | $6,899 |
| FieldRanger | Per technician; measurements from another tool | See [pricing](/pricing) |
At 100 roofs, the flat subscriptions cost less than the per-roof models, and Hover Pro pays for itself against Starter once a contractor measures 50 roofs a year. The commercial picture is different: 20 commercial bids with EagleView Premium reports cost $1,790 at Bronze, or $980 with Bid Perfect, against $1,699 for a year of Square Takeoff and $3,588 for a year of STACK Premium measured in-house.
Bid test on one steep-slope house and one low-slope building
- Pick a house with 6 to 8 facets that the crew has already roofed, and a flat-roofed building with drains and parapets from a past bid, with the squares and materials from both jobs.
- Measure the house in iRoofing, Hover or RoofLink, and order one EagleView report on it for comparison.
- Run the low-slope building through The EDGE and STACK from the same plans, including tapered insulation and parapet flashing.
- Price both with the contractor's own material costs, waste factors and labor.
- Send the steep-slope proposal with two options for signature.
- Verify: the measured squares on the house fall within 3% of the installed squares, and the low-slope takeoff's insulation boards and fasteners match the supplier's list from the original job.
Frequently asked questions
What is the best estimating software for roofing contractors?
For residential reroofers pricing at the house, iRoofing, Hover or RoofLink. For commercial roofers bidding low-slope work from plans, The EDGE or STACK, with Square Takeoff for plan takeoff without a contract. For purchased measurement reports, EagleView. For roofers whose estimates and crews run from HubSpot deals, FieldRanger, on vendor pages checked 13 November 2026.
What is the best commercial roofing estimating software?
The EDGE names tapered insulation, standing seam and poured deck modules with fastener counts, and STACK covers flat and low-slope roofs from plans and aerial images at $299 a user a month billed annually. EagleView sells Premium commercial reports from $79 to $89.50 by tier.
How much does roofing estimating software cost?
Published prices checked on 13 November 2026 run from $124 a month billed annually on iRoofing and $120 a user a month on RoofLink, the target of its price counter, to $399 a user a month on STACK Pro paid monthly. Hover charges $9 to $69 a roof measurement by plan and facets, and The EDGE quotes.
Which roofing estimating software includes measurements?
iRoofing includes unlimited DIY measurements and a $75 monthly imagery credit, and RoofLink states no per-measurement costs. Hover charges per project, EagleView per report, and STACK, Square Takeoff and The EDGE measure from plans the estimator loads.
Can roofing estimating software calculate tapered insulation?
The EDGE's Tapered Insulation module produces the material list and fastener counts, and its Poured Deck module lays out boards and lightweight concrete from drains and slope direction. The other tools here name no tapered insulation layout.
Does roofing estimating software work with HubSpot?
FieldRanger builds estimates on the HubSpot deal and syncs job photos to the HubSpot record. Hover Pro syncs with an unnamed CRM, RoofLink names SalesRabbit, and iRoofing, Square Takeoff, STACK's roofing page, The EDGE and EagleView name no HubSpot connection on the pages checked.
Roofing estimating vendor pages and check dates
All pages below were read with a plain request on 13 November 2026.
- iRoofing: pricing
- Hover: pricing
- RoofLink: pricing and homepage; RoofLink Pro on SalesRabbit pricing
- The EDGE: roofing and homepage
- STACK: takeoff and estimate pricing and roofing
- Square Takeoff: pricing
- EagleView: pricing
- SumoQuote: sumoquote.com/pricing redirects to jobnimbus.com/pricing, which blocks automated reads; not stated here
- FieldRanger features: fieldranger.ai/features
Counting roofs settles the residential choice and the drain layout settles the commercial one: a flat subscription wins once a contractor measures more than a few dozen houses a year, and tapered insulation is where only The EDGE names a module. A roofer whose pipeline already sits in HubSpot can compare that pipeline against best roofing CRM software, then run the estimate, the install and the invoice on one deal with Start free trial on pricing.
Run field service on HubSpot with FieldRanger
Estimates with e-signature, scheduling and dispatch, a technician mobile app and invoicing, synced to the HubSpot deals and contacts the business already keeps.
Book a demo