Guide
Delivery Route Planning:Stop Density, Time Windows, Vehicle Capacity, Driver Hours and a Costed Day
Delivery route planning as a method: stop density by zone, time windows, vehicle capacity and FMCSA driver hours, with a costed sample day for two vans.
Delivery route planning turns a day's orders into driver routes in a fixed order: group the stops into zones by density, mark each stop's time window, load each vehicle within its weight and volume, check every route against the driver's legal hours, then sequence the stops and compare the driven day with the plan.
A route built by sequencing alone looks efficient on the map and fails on the road. The van is full before the last zone, a 9 a.m. window sits at stop 40, and a box truck driver reaches the end of the legal duty window with six parcels on board. FieldRanger makes last mile delivery software that runs inside HubSpot, and this guide is one of its dispatching and scheduling guides. It sets out the inputs a route is built from, then stop density, time windows, vehicle capacity, federal driver hours, the method in order, a costed sample day, a checklist and the software record. App choice is a separate question, covered in the comparisons of the best delivery route planner app and the best route planner app.
Five terms recur. Stop density is the number of stops per route mile, or per hour of driving, in a zone. Service time is the minutes a driver spends at a stop, from parking to departure. A hard window is a delivery time the customer cannot move; a soft window is a preference the plan tries to meet. A commercial motor vehicle (CMV) is the federal class of vehicle to which the hours-of-service rules apply, defined below by weight.
Route planning for delivery: the inputs a route is built from
Route planning for delivery starts from the order list, and each order carries more than an address. A planner that has only addresses can sequence stops; it cannot tell which route is feasible.
| Input | What it decides | Source |
|---|---|---|
| Address and access notes | Zone, parking, dock or door | Order or customer record |
| Service time | Minutes added at each stop | Measured from past stops at the same kind of address |
| Time window, hard or soft | Where the stop can sit in the sequence | Customer order or account terms |
| Weight and volume | Which vehicle can carry it | Order lines or packing list |
| Proof required | Photo, signature or none, and the minutes it adds | Account terms |
| Vehicle and driver | Capacity limit and hours limit for the route | Fleet and staff records |
Service time deserves its own measurement. Two routes with the same miles differ by an hour when one route's stops are apartment buildings and the other's are loading docks, and a planner that assumes the same minutes everywhere overfills the first route.
Stop density and delivery zones
Stop density sets a large part of a stop's cost, because both of a route's large costs, the driver's hours and the vehicle's miles, are spread across the stops in it. A zone is drawn so that its stops can be served in one loop, and its boundary follows roads, bridges and traffic patterns rather than postal codes.
The arithmetic is short. A stop's cost is the route's driver cost plus its vehicle cost, divided by the stops on the route. Driver cost is the on-duty hours times the loaded hourly wage; vehicle cost is the miles times a per-mile rate. The Bureau of Labor Statistics reports a May 2025 median of $44,860 a year for light truck drivers, and $21.13 an hour for delivery truck drivers and driver/sales workers as a group (BLS Occupational Outlook Handbook, modified August 27, 2026). The IRS business standard mileage rate is 76 cents a mile from July 1, 2026 (IRS, updated July 28, 2026).
Density also decides how a zone is split between vehicles. Two vans sharing one zone's stops both cross the whole zone, and their paths overlap street by street; two vans that each own half of it cover compact areas with shorter gaps between stops. A zone that one van cannot finish within its hours is split along a road, not shared.
Delivery time windows: hard, soft and open
A time window fixes where a stop can sit in the sequence, so windows are placed before anything is optimized. Hard windows go in first, because a route that misses one has failed regardless of its mileage. Soft windows go in next, ranked by the account's terms. Open stops fill the gaps between them.
Narrow windows constrain the plan before any sequencing is done. A two-hour window at 9 a.m. pulls one van into that zone first thing; three such windows in three different zones cannot all be met by one van, and the planner either moves a stop to another vehicle or asks the customer for a wider window before the route is built. A window is feasible only when the drive from the previous stop, plus that stop's service time, lands inside it with a margin left for traffic.
Windows also set the cost of a late order. An order added at 10 a.m. with an 11 a.m. hard window is inserted into the route whose position at 11 a.m. is nearest, and every stop after it moves later; the insertion is accepted only if none of those later stops falls out of its own window.
Vehicle capacity: payload, volume and the 10,001-pound line
Capacity has three limits, and a route must stay inside all of them: the weight the vehicle may carry, the cubic feet it holds, and the stop count a driver can unload in the hours available. Weight and volume are checked at loading; a van that fits the parcels by weight and not by volume leaves stops on the dock.
Weight also decides which federal rules apply. Under 49 CFR 390.5T, a commercial motor vehicle includes a vehicle used in interstate commerce with a gross vehicle weight rating or gross combination weight rating "of 4,536 kg (10,001 pounds) or more". Interstate commerce, defined in the same section, includes transport between a place in one state and a place outside it. A cargo van rated below that line is outside the federal hours-of-service rules discussed next; a box truck rated above it and crossing a state line is inside them. Intrastate operations answer to the state's own motor carrier rules, which the carrier checks separately.
Loading order follows the sequence. The last stop goes in first, and the first stop sits nearest the door, so a route resequenced after loading costs minutes at every stop.
Driver hours under FMCSA rules
For a CMV in interstate commerce, the driver's legal hours bound the route. Under 49 CFR 395.3, a property-carrying driver may not drive without first taking 10 consecutive hours off duty, may not drive after 14 consecutive hours after coming on duty, may drive a total of 11 hours within that period, and may not drive once more than 8 hours of driving have passed without a 30-minute interruption. The weekly limits are 60 hours on duty in 7 days for a carrier that does not operate every day, and 70 hours in 8 days for one that does, with a restart after 34 or more consecutive hours off duty.
Local delivery with a CMV can qualify for the short-haul provisions of 49 CFR 395.1, which change the records and, for non-CDL drivers, the duty window.
| Provision | Limit | Records |
|---|---|---|
| Standard, § 395.3 | 11 hours driving within 14 hours on duty, after 10 hours off; 30-minute break after 8 hours of driving | Records of duty status |
| Short haul, § 395.1(e)(1) | Within 150 air miles of the work reporting location; released within 14 consecutive hours; 10 hours off between | Carrier keeps time records for 6 months: report time, total hours, release time |
| Non-CDL short haul, § 395.1(e)(2) | Within 150 air miles; return to the work reporting location each day; no driving after the 14th hour on duty on 5 days, or after the 16th hour on 2 days, in any 7 consecutive days | Time records for 6 months, as above |
| Adverse driving conditions, § 395.1(b)(1) | Up to 2 additional hours to complete the run or reach a safe place | As for the route's provision |
The planning rule follows from the table. A route's on-duty hours, from the start of loading to release at the depot, are computed before dispatch and kept inside the provision that applies, with the 30-minute break placed in the sequence where the standard rule requires it. The short-haul provisions are exempt from the 8-hour break rule, as § 395.3(a)(3)(ii) states.
Planning a delivery route: the method in order
Planning a delivery route repeats the same steps every day, and the order matters because each step narrows the next.
- Close the order list at a fixed cut-off and attach weight, volume, window and proof requirements to each order.
- Assign each stop to a zone, and estimate each zone's driving and service hours from past routes.
- Assign zones to vehicles by capacity, splitting a zone along a road where one vehicle cannot hold it.
- Place hard windows, then soft windows, then open stops in each vehicle's sequence.
- Compute each route's on-duty hours, from loading to release, and check them against the hours provision that applies.
- Load each vehicle in reverse stop order.
- Re-plan inserted orders against the windows of the stops that follow them.
- Compare the driven route with the plan after release: miles, on-duty hours, stops completed and windows missed.
The courier business plan template carries the same inputs into a yearly plan for a new delivery company: routes, vehicles and the cost per stop the price list must cover.
Sample delivery day: two vans and 120 stops
The day below is a sample for a hypothetical courier with two cargo vans rated under 10,001 pounds, so the federal hours rules do not apply, though the duty hours are still computed. The wage, the compensation share and the mileage rate are published figures. The stops, service time, hours and miles are sample inputs, and the two plans serve the same 120 stops.
Plan A groups the stops into two zones by density and sequences each zone. Plan B splits the stops between the vans in the order they were received. Each van spends 0.75 hours loading, 4.0 hours at stops (60 stops at 4 minutes) and 0.5 hours on a break.
| Line | Plan A: zoned by density | Plan B: order received |
|---|---|---|
| Driving per van | 3.5 hours, 80 miles | 5.5 hours, 135 miles |
| On-duty hours per van | 8.75 | 10.75 |
| Driver cost per van at $30.81 an hour | $269.59 | $331.21 |
| Vehicle cost per van at $0.76 a mile | $60.80 | $102.60 |
| Cost per van | $330.39 | $433.81 |
| Cost of the day, two vans | $660.78 | $867.62 |
| Cost per stop | $5.51 | $7.23 |
The driver rate is the light truck driver median, $44,860 ÷ 2,080 hours = $21.57, divided by 0.700 because wages and salaries were 70.0 percent of private industry compensation in June 2026 (BLS Employer Costs for Employee Compensation, released September 9, 2026). The IRS rate is used here as an all-in vehicle cost per mile, a modeling choice rather than a measured cost. Fuel alone is a part of it: regular gasoline averaged $3.995 a gallon in the week of November 9, 2026 (EIA), which is about 22 cents a mile for a van at a sample 18 miles per gallon.
The difference between the plans is $206.84 a day, or $51,710 over a sample 250 working days, and it comes entirely from two hours of driving and 55 miles per van. Neither van breaks a limit in Plan B, so a scattered plan survives day after day: it fails on cost, quietly, rather than on hours. A box truck above 10,001 pounds on the same Plan B route would also stay within the 14-hour window, so the hours check does not catch it either; only the cost per stop does.
Route delivery planning checklist
- Order cut-off time fixed and published to customers.
- Service time measured by stop type, not assumed.
- Every order carries weight, volume, window and proof requirement before planning starts.
- Zones drawn on roads and traffic patterns, one vehicle per zone where capacity allows.
- Hard windows placed before soft windows and open stops.
- Each route's on-duty hours computed and checked against the hours provision that applies, with time records kept for six months where § 395.1(e) is used.
- Vehicles loaded in reverse stop order.
- Cost per stop calculated for the day and compared with the price per stop.
- Driven miles, hours, completed stops and missed windows recorded against the plan.
Delivery routes and proof of delivery in FieldRanger
The checklist ends on comparison, which needs each stop recorded as a job. In FieldRanger, each driver's route for the day is built automatically, stops are sequenced to cut drive time and fuel cost, and routes adjust when priorities change or jobs are added. Arrival windows are set and tracked for on-time performance, job-to-job travel time and mileage are estimated, and service zones can be defined with drivers assigned to them. Route history shows past routes against the next ones. The route optimization software page covers the routing features.
At the stop, the driver records before and after photos on the work order and a customer signature as proof of completion, and status updates are visible to the dispatcher in real time. Vehicles carry real-time GPS location on a live map, odometer logging supports IRS mileage records, and digital pre-trip and post-trip inspection checklists sit with each vehicle. Business accounts, their contacts and their invoices stay on the same HubSpot records. Plans are on pricing, and Start free trial runs for 14 days without a card.
Frequently asked questions
What is delivery route planning?
It is the daily work of turning orders into driver routes: grouping stops into zones by density, placing time windows, loading vehicles within capacity, checking driver hours, sequencing the stops and comparing the driven route with the plan.
How to plan a delivery route?
Close the order list, attach weight, volume and window to each order, assign stops to zones, assign zones to vehicles by capacity, place hard windows first, check on-duty hours, load in reverse stop order and review the driven route once the vans are back.
What is route planning for delivery drivers versus dispatchers?
Dispatchers build the zones, assign vehicles and place the windows; drivers work the sequence, load in reverse order and record each stop. The driver-side steps are covered in the guide to route planning for delivery drivers.
Do FMCSA hours-of-service rules apply to delivery vans?
They apply to commercial motor vehicles in interstate commerce, which include vehicles rated at 10,001 pounds or more. A cargo van rated below that line is outside them; a box truck above it that crosses a state line is inside them, and can qualify for the short-haul provisions of 49 CFR 395.1(e).
How many stops can a delivery driver make in a day?
The count follows from service time, driving time and the hours limit, not from a fixed number. In the sample day, a van serves 60 stops at 4 minutes each with 3.5 hours of driving, for 8.75 hours on duty.
What does a delivery stop cost?
Driver hours times the loaded wage, plus miles times a per-mile rate, divided by the stops on the route. In the sample, a zoned plan costs $5.51 a stop and an unzoned plan $7.23 for the same 120 stops.
Plan B in the sample breaks no rule and misses no window, so the day's exceptions report is empty; the $1.72 it adds to every stop appears only when the driven miles and hours are set against the plan once the vans are back at the depot.
Run field service on HubSpot with FieldRanger
Estimates with e-signature, scheduling and dispatch, a technician mobile app and invoicing, synced to the HubSpot deals and contacts the business already keeps.
Book a demo