Industry

HVAC Estimating Software:HVAC Estimates in FieldRanger and HubSpot

HVAC estimating software on HubSpot: price repairs, maintenance agreements and replacements on the deal or in FieldRanger, and turn the won deal into the job.

Updated 8 min read

HVAC estimating software prices heating and cooling work before the customer agrees to it: a repair quote, a maintenance agreement or a system replacement proposal. FieldRanger builds the estimate from the HubSpot deal or contact record, or in FieldRanger tied to that deal, and turns the won deal into the install job.

Estimating is the sales half of HVAC software. It fixes what equipment goes into the house and at what price. The job, the work order and the invoice all descend from it. A replacement estimate written in 2026 also carries three inputs that changed after 2022: regional efficiency minimums, the refrigerant transition and the end of a federal tax credit. Each is set out below with its source.

HVAC quotes, proposals and bids by type of work

Four prices leave an HVAC office, and HVAC quote software, HVAC proposal software and HVAC bidding software are each sold for one of them.

A repair quote prices a fault the technician has already diagnosed: a failed capacitor, a burnt contactor, an igniter, a leak search and recharge. The homeowner approves it on site. The price comes from the contractor's flat-rate sheet, or from hours at the labor rate plus parts.

A maintenance agreement quote prices a year of visits rather than one repair: a cooling check in spring, a heating check in fall, and filters. Once the agreement is sold, recurring job templates in FieldRanger hold its visits.

A replacement proposal prices a new system: condenser or heat pump, furnace or air handler, evaporator coil, line set, thermostat, pad, disconnect, permit and haul-away. A comfort advisor presents it in the home. It can offer two or three systems at different efficiency levels.

A commercial bid prices a mechanical scope from drawings, in competition: rooftop units, duct runs taken off by size and gauge, piping, controls, and test and balance.

FieldRanger serves the first three. The fourth starts from a quantity takeoff on plans, which FieldRanger does not perform.

Load, efficiency and refrigerant inputs to a replacement estimate

A replacement estimate rests on three technical decisions and one financial one. A standard outside the software fixes each of them.

Equipment size. Capacity comes from a load calculation, not from the tonnage of the old unit. ACCA describes Manual J as "the national ANSI-recognized standard for producing HVAC equipment sizing loads", and groups it with Manual S for equipment selection and Manual D for duct design (ACCA, Manual J, checked November 2026). FieldRanger does not calculate loads; the calculation runs in design software before the price is written.

Minimum efficiency. Since January 1, 2023, split-system central air conditioners must reach 13.4 SEER2 in the North. In the Southeast and Southwest the minimum is 14.3 SEER2 below 45,000 Btu/h and 13.8 SEER2 at or above it, and split-system heat pumps must reach 14.3 SEER2 and 7.5 HSPF2 nationwide (U.S. Department of Energy, 2023 central air conditioner standards FAQ, issued October 5, 2022). In the two southern regions the rule follows the installation date, not the manufacture date. A condenser below the regional minimum cannot be quoted for a new install there, whatever its age.

Refrigerant. The EPA's Technology Transitions rule sets a global warming potential limit of 700 for new residential and light commercial air conditioning and heat pump systems from January 1, 2025. Systems whose components were all made or imported before that day have no installation deadline (EPA, Technology Transitions restrictions by sector, updated August 28, 2026). The refrigerant on an estimate therefore depends on when the equipment was built, not only on its model.

Federal tax credit. The IRS states that the Energy Efficient Home Improvement Credit "is allowed for qualifying property placed in service on or after Jan. 1, 2023, and before December 31, 2025", with heat pumps capped at $2,000 a year (IRS, Energy Efficient Home Improvement Credit, reviewed April 28, 2026). A 2026 heat pump proposal that still deducts the credit overstates the savings. Utility and state rebates are separate programs.

Replacement estimate from repair call to scheduled install

An HVAC replacement estimate passes through six records, from the repair call to the install on the calendar.

  1. A technician on a no-cool call finds a failed compressor and photographs the data plate and the failed part. The photos attach to the work order and sync to the customer's HubSpot record.
  2. The office opens a replacement deal on the same HubSpot contact. The model number, the equipment's age and the technician's notes are already on the HubSpot timeline.
  3. The comfort advisor runs the load calculation and selects equipment that meets the regional SEER2 minimum. The estimate is built in one of two places: from the HubSpot deal record without leaving HubSpot, or in FieldRanger, where it stays tied to the deal.
  4. The estimate and the agreement go to the homeowner for signature through PandaDoc.
  5. The signed deal is marked won. FieldRanger creates the install job with the deal's context carried over, and the deal record shows the job's status from then on. A deposit invoice can go out before the install, with the balance invoiced on completion.
  6. The dispatcher drags the install onto a certified technician's calendar; the HVAC dispatch software page covers that step. After commissioning, the customer signs on site and the invoice is generated from the completed work order.

Nobody retypes the customer, the address or the equipment history after step 1. Each later record inherits them from the HubSpot contact and deal.

Tiered options in an HVAC sales proposal

HVAC sales proposal software presents more than one price for the same house. A three-option proposal might offer a single-stage air conditioner at the regional minimum, a two-stage unit at a higher SEER2 rating, and a variable-speed heat pump. The homeowner weighs the upfront price against comfort and the utility bill.

FieldRanger builds the estimate on the deal, and the estimate writes the HubSpot deal's line items and amount. ServiceTitan lists "Good-Better-Best proposals" built from a centralized pricebook, with "financing options" on the proposal (ServiceTitan, HVAC estimating, checked November 2026). A replacement shop that sells on tiered options and financing at the kitchen table is better served by that kind of tool. ServiceTitan's estimating page names no HubSpot integration.

Estimated labor against installed labor

An estimate predicts hours and materials, and the install tests the prediction. FieldRanger records both sides on the job.

Labor is recorded as clock-ins and clock-outs against the install job, each with the technician's location, and one job carries the installer and the helper together. A two-day changeout is two jobs, one per day, since multi-day jobs are not built, and each day's clock-ins carry their locations. Materials, from the coil and line set to the disconnect and the refrigerant, are logged against the job for job costing. Parts checked out of a specific warehouse are counted where the stock actually sits.

Revenue reports show job revenue and margin by customer or service type. Read across a cooling season, the comparison corrects the next estimate. If attic air handler replacements earn less margin than basement furnace swaps, the attic price needs more labor hours, and the gap shows by service type rather than from memory.

Commercial HVAC estimating and bidding software

Commercial HVAC estimating software starts from the drawings. A mechanical estimator takes off duct runs, fittings, diffusers and equipment from the plans, then applies labor units. FastDUCT, for example, supports takeoff of "rectangular, round, and oval ductwork as well as sheet metal and HVAC equipment" directly on digital plans (FastDUCT, checked November 2026). FieldRanger does not measure quantities from plans. A sheet metal or mechanical contractor that wins work by bidding from drawings needs a takeoff tool of that kind.

FieldRanger fits the commercial service side: a rooftop unit repair quote for a property manager, a planned maintenance agreement for a building, or a replacement priced for an owner who is already a HubSpot contact. Skill-based assignment then matches each job to a technician by certification and expertise.

Scope of FieldRanger estimating for HVAC contractors

  • FieldRanger does not calculate heating and cooling loads, select equipment or size ducts. Manual J, S and D work happens in design software.
  • FieldRanger does not take off quantities from mechanical drawings.
  • Signature on the estimate runs through the PandaDoc integration.
  • Prices on the estimate come from the estimator. FieldRanger records the actual labor and materials for comparison afterwards.

Frequently asked questions

What is HVAC estimating software?

Software that prices heating and cooling work before the customer agrees to it, from a repair quote to a full system replacement proposal. In FieldRanger, the estimate is built from the HubSpot deal or contact record or in FieldRanger, and the won deal becomes the install job.

What is the difference between an HVAC quote and an HVAC proposal?

A quote prices a single defined fix, such as a capacitor replacement, at a stated price. A proposal prices a new system with its equipment, labor, permit and terms, and can offer several systems at different efficiency levels.

Can HVAC estimates be built inside HubSpot?

Yes. FieldRanger lets a comfort advisor build an estimate from the HubSpot deal or contact record without leaving HubSpot. An estimate built in FieldRanger instead stays tied to the same deal.

What SEER2 rating does a new central air conditioner need?

Under the Department of Energy standards in force since January 1, 2023, a split-system air conditioner needs 13.4 SEER2 in the North. In the Southeast and Southwest it needs 14.3 SEER2 below 45,000 Btu/h and 13.8 SEER2 at or above it.

Is the federal heat pump tax credit available in 2026?

Not for new installs. The IRS states that the Energy Efficient Home Improvement Credit applies to qualifying property placed in service before December 31, 2025, so a 2026 proposal should not deduct it.

What software do commercial HVAC estimators use?

Takeoff and estimating software that measures ductwork, piping and equipment from drawings and applies labor units, such as FastDUCT for sheet metal. Field service software such as FieldRanger covers commercial service quotes and maintenance agreements rather than plan-based bids.

Is there a free HVAC estimating app?

Spreadsheet and document templates produce an HVAC estimate at no cost, with no link to the CRM, the job or the install's actual costs. FieldRanger offers a 14-day free trial with no card required.

HVAC estimates in FieldRanger

A replacement estimate in FieldRanger starts from the repair visit's photos on the HubSpot record and ends as an install job on the dispatcher's calendar. The rest of the trade's workflow is on the HVAC software page, and the install's place on the calendar is covered by HVAC dispatch software. Plans are priced per technician on pricing; Start free trial runs 14 days with no card.

FieldRanger runs field service inside HubSpot

Estimates, scheduling and dispatch, a technician app and invoicing on the HubSpot records sales already keeps. Every plan starts with a free trial.

Book a demo