Industry

HVAC Inventory App:HVAC Inventory in FieldRanger and HubSpot

HVAC inventory app on HubSpot: FieldRanger checks parts and refrigerant out of a specific warehouse, logs them against each job and warns when stock runs low.

Updated 8 min read

An HVAC inventory app records which parts, equipment and refrigerant a heating and cooling contractor holds, where each item sits and which job used it. FieldRanger keeps that record inside HubSpot: technicians check stock out of a specific warehouse, the materials used are logged against each job, and low-stock warnings prompt the reorder.

Inventory is the supply side of HVAC software. A changeout cannot start until the condenser, coil and line set are on the truck, and a no-cool call becomes a second visit when the right capacitor is not. The general mechanics of warehouse checkout are on warehouse inventory management software; this page covers the stock particular to heating and cooling work.

Warehouse stock and truck stock

HVAC stock sits in two places. Warehouse stock is the equipment and bulk material held at the shop or a branch: condensers, furnaces, air handlers, evaporator coils, line sets, pads and duct fittings. Truck stock is what a service technician carries to finish a repair on the first visit: run capacitors in common microfarad ratings, contactors, igniters, flame sensors, fuses, filters in common sizes and refrigerant.

FieldRanger counts stock by warehouse. A technician checks parts and materials out of a named warehouse, and that warehouse's count drops by what was taken. The parts used on site are then logged against the job. Each technician's truck can also be its own stock location, so a van carries its own count and parts are checked out of it the same way. A capacitor moved to restock a truck leaves the warehouse figure, and it reaches a job record when it is logged on one.

A contractor that tracks every part by serial number from receiving dock to van is better served by a dedicated inventory tool. inFlow, for example, describes scanning equipment "to transfer it from the warehouse to each service truck" and tracking "serial numbers for any part". Its HVAC page does not mention HubSpot (inFlow, HVAC inventory software, checked November 2026).

Refrigerant cylinders and the Section 608 sales restriction

Refrigerant is the stock item with a federal purchase rule attached. EPA's sales restriction lets technicians who have earned the Section 608 Technician Certification buy refrigerant. An employer may buy it on giving the wholesaler "written evidence that he or she employs at least one properly certified technician." The wholesaler keeps invoices showing the purchaser's name, the date of sale and the quantity purchased (EPA, refrigerant sales restriction, updated March 23, 2026). Certification also governs the work that draws on those cylinders: under EPA's rule, servicing, repairing or disposing of equipment that could release ozone-depleting refrigerant requires it (EPA, Section 608 technician certification, updated March 3, 2026).

The cylinders on the shelf were therefore bought on the strength of the business's certified technicians. FieldRanger's skill-based assignment matches refrigerant jobs to technicians by certification, so a recharge goes to a technician who holds the right Section 608 type. The control sits at the job assignment rather than at the warehouse checkout. The refrigerant added on each job is logged against the job as a material, with the pounds written into the work order notes.

Recovery cylinders and recovery machines come back to the shop after each job, so they belong with equipment rather than consumable stock. FieldRanger's asset tracking checks equipment in and out by scanning its QR code on a phone. It keeps a usage history of who had which item and when, and schedules maintenance for each piece.

R-410A equipment and manufacture dates

The AIM Act transition attaches a date to some of the equipment in stock. EPA's table of restrictions sets a 700 GWP limit for residential and light commercial air conditioning and heat pump systems, with an installation compliance date of January 1, 2025. The same table lists "No installation compliance date for systems where all specified components were manufactured or imported prior to January 1, 2025." Components used to repair existing systems are not subject to these restrictions (EPA, technology transitions HFC restrictions by sector, updated August 28, 2026). EPA's questions page on the HFC phasedown adds that specified components made with R-410A after January 1, 2025 must be labeled "for servicing existing equipment only". That page still describes January 1, 2026 as a cutoff for installing a new R-410A system (EPA, frequent questions on the phasedown of hydrofluorocarbons, updated September 14, 2026).

Two R-410A condensers on the same shelf can therefore carry different permissions. A unit made before 2025 can go into a new installation under the table's exemption, provided every specified component of that system also predates 2025. A unit made after that date carries the servicing label and goes to repairs of existing systems. The two EPA pages differ on the date for installing pre-2025 equipment, so the contractor confirms the current rule with the distributor before quoting one. In either reading, the deciding fact for each unit is its manufacture date, taken from the data plate or the serial number.

FieldRanger keeps the manufacture date and serial number on the job. The technician photographs the data plate of each unit installed or removed, and the photos attach to the work order, from which HubSpot receives them on the customer's record. The serial number can be typed into a HubSpot custom property on the same record.

Equipment serial numbers and warranty registration

The serial number matters again after the install. Carrier's warranty page asks for eligible equipment to be registered within 90 days of installation. Without registration, the page states, "the standard 5-year parts-only limited warranty will apply" (Carrier, warranty registration and information, checked November 2026). Registration is per unit, so the job record needs the data plate of every condenser, furnace and air handler installed, and the date of installation.

In FieldRanger, the installation date is the date the job was completed, and the data plates are in the photos on its work order. A job status change can trigger a HubSpot workflow, so completing a changeout can create the office's registration task while the manufacturer's window is open. HubSpot's pricing page for Sales Hub sets the limit at 50 workflows on Starter, with restricted triggers and actions, and 300 on Professional (HubSpot, Sales Hub pricing, checked November 2026).

A changeout from warehouse shelf to job cost

  1. The replacement deal is marked won in HubSpot, and the won deal becomes the install job, its context carried over.
  2. The dispatcher assigns the install to a technician. Calendar and certification matching are covered on HVAC dispatch software.
  3. The crew checks the condenser, coil, line set, pad and disconnect out of the warehouse that holds them, and each item comes off that warehouse's count.
  4. On site, the technician photographs the data plates of the old and the new equipment. Refrigerant recovered from the old system goes into a recovery cylinder checked out by QR code.
  5. Parts and materials used, including any refrigerant added, are logged against the job.
  6. The customer signs on completion, and the invoice is generated from the completed work order.
  7. Revenue reports show revenue and margin by customer or service type, built from the materials and hours logged on jobs like this one, and low-stock warnings flag what the next install will need.

Billing for the changeout is covered on HVAC invoice software.

Seasonal parts and low-stock warnings

The parts a service technician reaches for change with the season. Cooling calls draw on run capacitors, contactors and condenser fan motors; heating calls draw on hot surface igniters, flame sensors and inducer motors. A warehouse stocked for July runs short in November unless its reorder levels move with the season.

FieldRanger's inventory alerts send low-stock warnings and reorder reminders for each warehouse, and the order itself goes through the distributor's portal or the accounting system. Materials logged per job record which parts each season consumed. A custom report of those materials, exported to Excel or CSV, gives the owner the figures for next year's levels.

Limits of FieldRanger for HVAC inventory

  • No serial-number or manufacture-date tracking for stocked units; data plate photos and HubSpot properties carry them on the job.
  • No purchase orders to suppliers; low-stock warnings and reorder reminders only.
  • QR check-in and check-out applies to equipment such as recovery machines and cylinders, not to consumable parts.
  • No refrigerant leak-rate log; records for EPA leak repair duties are kept outside FieldRanger.

FieldRanger fits the HVAC contractor that sells in HubSpot and wants each part tied to the job, and the job to the deal behind it. A contractor whose first need is each unit tracked by serial number from receiving dock to install is better served by a dedicated inventory tool.

HVAC inventory guides and sibling pages

The trade as a whole is on HVAC software, with the calendar on HVAC dispatch software and billing on HVAC invoice software. Inventory across trades is on warehouse inventory management software, and the free HVAC maintenance checklist lists the tune-up steps whose filters and parts the warehouse supplies. Plans are priced per technician on pricing.

Frequently asked questions

What is an HVAC inventory app?

An app that records the parts, equipment and refrigerant an HVAC contractor holds, where each item sits and which job used it. FieldRanger does this inside HubSpot, with checkout from a specific warehouse, materials logged per job and low-stock warnings.

What is the difference between truck stock and warehouse stock?

Warehouse stock is the equipment and bulk material held at the shop or a branch. Truck stock is the set of repair parts and refrigerant a technician carries to finish a call on the first visit. FieldRanger counts stock by warehouse, and each technician's truck can be its own stock location.

Who can buy refrigerant for HVAC work?

Under EPA's sales restriction, technicians with Section 608 certification, and employers who give the wholesaler written evidence that they employ at least one certified technician. The wholesaler keeps a record of each purchaser, date and quantity.

Can HVAC inventory software track equipment serial numbers?

Dedicated inventory tools track serial numbers per unit. FieldRanger records them on the job instead: data plate photos attach to the work order and sync to the customer's HubSpot record, and a HubSpot custom property can hold the serial number.

Can R-410A condensers in stock still be installed?

It depends on the unit's manufacture date. EPA's restrictions table lists no installation compliance date for systems whose specified components were all made or imported before January 1, 2025, and components made with R-410A after that date are labeled for servicing existing equipment only. The contractor confirms the current rule before quoting.

Does FieldRanger create purchase orders for HVAC parts?

No. FieldRanger sends low-stock warnings and reorder reminders; the purchase order goes through the distributor or the accounting system.

A condenser checked out in FieldRanger shows up three times: off the warehouse count, on the install job and, with its data plate photographed, on the HubSpot deal that sold it. The calendar that books those installs is on HVAC dispatch software, the rest of the trade on HVAC software, and the plans on pricing. Start free trial: 14 days, and no card is asked for.

FieldRanger runs field service inside HubSpot

Estimates, scheduling and dispatch, a technician app and invoicing on the HubSpot records sales already keeps. Every plan starts with a free trial.

Book a demo