Comparison

Best Estimating Software for Concrete Construction:Cubic-Yard Takeoff, Rebar Assemblies and Seat Prices for Eight Tools

Best estimating software for concrete construction compared: STACK, PlanSwift, eTakeoff, Kreo, Square Takeoff, The EDGE, OneCrew and FieldRanger on seat prices.

By Published Updated

14 min read

The best estimating software for concrete construction depends on who prices the pour. Commercial subcontractors bidding from plans suit STACK, PlanSwift, eTakeoff or The EDGE; small crews on a budget suit Square Takeoff or Kreo; paving and flatwork contractors measuring from maps suit OneCrew; and residential contractors selling through HubSpot suit FieldRanger.

A concrete estimate is a volume problem before it is a price: every footing, wall and slab becomes cubic yards, every edge becomes linear feet of form, and every mat becomes tons of rebar. A tool that measures areas but not depths leaves the yardage to a spreadsheet. The general contractor software page shows how FieldRanger runs the job after the bid, and head-to-head pages for field service products sit in the field service software comparisons hub.

The comparison defines the concrete takeoff terms, states the criteria and sets eight tools side by side by seat price. Entries follow in four groups: plan takeoff with estimating, low-cost cloud takeoff, an estimator built for concrete trades and a paving platform, then FieldRanger. A section on subcontractor bids, a capability table, a year-one cost for one seat and a bid test close it before the questions. Each vendor fact was read on that vendor's own page with a plain request on 13 November 2026; review-site ratings play no part. FieldRanger publishes this comparison and makes one of the products in it.

Concrete takeoff terms: yardage, formwork, rebar, assemblies and waste

A takeoff is the measurement of quantities from drawings: areas, lengths, counts and, for concrete, depths. Cubic yardage is length times width times depth, divided by 27 cubic feet a yard. Formwork is measured in linear feet of edge or square feet of contact area, and rebar in pounds or tons from bar size, spacing and laps. A waste factor adds a percentage to the yardage for overpour and spillage.

An assembly is a saved recipe that turns one measurement into every line it implies: a 24-inch footing assembly produces the yards, the form, the rebar, the labor to place and finish, and the pump. Estimating applies prices and labor rates to those lines and produces the bid. A takeoff-only tool stops at quantities and exports them; a takeoff-and-estimating tool carries the same measurement through to the proposal.

Criteria for concrete estimating software

  1. Volume takeoff with depth, giving cubic yards for footings, walls, slabs and piers.
  2. Rebar and formwork calculated from the same measurement.
  3. Assemblies and a cost database the estimator can edit.
  4. Labor rates that change with the element, not one rate per yard.
  5. Drawing comparison when a revised set arrives before bid day.
  6. Proposal output with inclusions and exclusions, or an Excel export.
  7. Seat price, billing term and trial, dated.
  8. Where the bid goes after it is won: job costing, scheduling and the CRM.

Eight concrete estimating tools by seat price

Entry seat price, billing basis and trial, from vendor pages checked 13 November 2026
ToolEntry seat priceBilling basisTrial or free version
eTakeoff DimensionAdvanced $795 a user a yearAnnual subscriptionFree trial
KreoEssential $100 a user a monthBilled annually, $1,200 a year7-day trial
Square Takeoff$249 a monthMonth to month, $599 a quarter or $1,699 a year14-day trial
PlanSwiftEssential $2,000 a yearAnnual, 1 seat14-day trial, no card
STACKPremium $299 a user a monthBilled annually; 12-month termFree version; 7-day Pro trial
The EDGENot publishedDemoNot stated
OneCrewNot publishedPricing page not foundNot stated
FieldRangerPer technicianSee [pricing](/pricing)14 days, no card

Every published price here is per seat, and every annual figure is paid for one estimator. A two-estimator office doubles each line before any seat discount, which PlanSwift mentions without printing and eTakeoff quotes by phone for enterprise licensing.

Plan takeoff with estimating for commercial subcontractors

STACK: cubic yards, rebar as measured, and proposals on Pro

Best for: concrete subcontractors with several estimators who want cloud takeoff, shared projects and proposals in one subscription. Price: Premium is $299 a user a month billed annually or $349 paid monthly; Pro is $349 or $399. The FAQ states that every Takeoff and Estimate subscription is a 12-month term, paid upfront or spread monthly (STACK takeoff and estimate pricing, checked 13 November 2026).

Strengths: the concrete page describes takeoff by pounds, linear feet or cubic yards, rebar accounted for as the estimator measures, a library of pre-built concrete items, and material, labor and equipment costs for concrete and paving bids. Premium includes unlimited projects and measurements, the full takeoff toolset, a pre-built item and assembly library, drawing overlays, AI takeoffs and unlimited viewer seats. The plan grid marks material and labor estimating with items and assemblies on Premium and Pro, though the Pro card lists it as a Pro addition. Pro adds worksheet-style estimates, STACK for Excel, a regional BNI cost library and native proposals. A free version allows 1 active project a month, 300 plan pages and 50 measurements a project. Falls short on: proposals start on Pro, so the quote should confirm what Premium's estimating covers. Aerial image takeoff is an add-on requiring Premium, and ERP connectors an add-on requiring Pro, both unpriced. The page also contradicts itself on price: its embedded product data gives Premium at $249 and Pro at $299 billed annually, and its header promises 15% off annual billing where the FAQ says 20%.

PlanSwift: footings, slabs and formwork priced in one pass

Best for: estimators who want takeoff and estimating in one tool, with pre-built concrete assemblies, on one annual seat. Price: Essential is $2,000 a year for one seat and Core $3,000, with discounted pricing for added seats and possible volume pricing from 10 licenses. The 14-day trial needs no card and does not convert automatically (planswift.com/pricing, checked 13 November 2026).

Strengths: the concrete page describes footings, slabs, walls and piers measured and priced with materials, labor and waste. It applies the estimator's logic to cubic yardage and reinforcing and uses pre-built assemblies for rebar and membranes. A live Excel integration feeds existing pricing sheets, and drawing comparison flags changed footing or slab dimensions. Essential includes Auto Count, Auto Scale and Auto Bookmark, priority support and 2 hours of one-to-one training; Core adds Auto Takeoff for a first-pass takeoff of areas, lengths and counts. Falls short on: the added-seat discount is not printed, and the pages name no proposal document or bid management; they present Excel as the route into existing pricing sheets. The general bid comparison, including PlanSwift's place among takeoff tools, is in best construction estimating software.

The eTakeoff Dimension plans: work zones, phases and assemblies with logic on Premier

Best for: commercial concrete estimators who pour in phases and need quantities split by zone and coded to a work breakdown structure for an existing estimating system. Price: Advanced is $795 a user a year and Premier $1,495; the Togal.ai AI takeoff add-on costs $1,800 a user a year on either (etakeoff.com/pricing, checked 13 November 2026).

Strengths: both plans include drawing overlays, native PDF viewing, true multi-user access, advanced Excel integration, multiple scales on one drawing, layers and WBS coding. Premier adds SnapAI, pattern search and autocount, work zones and phases, user-defined assemblies with logic and project-wide variables. Falls short on: assemblies, zones and phases all start on Premier, and the pages describe takeoff feeding an estimate, not a proposal. The subscription agreement on the pricing page is Togal.ai's, and the page states that enterprise licensing is quoted by phone.

Low-cost cloud takeoff for small crews

Square Takeoff: one price with every feature, from $249 a month

Best for: small concrete contractors who want cloud takeoff with no contract and every feature on the cheapest plan. Price: $249 a month month to month, $599 a quarter or $1,699 a year, with unlimited jobs and storage; multiple licenses are quoted by phone (squaretakeoff.com/pricing, checked 13 November 2026).

Strengths: the concrete page describes cubic yards for slabs, footers, poured walls and rebar from uploaded blueprints. The pricing page lists blueprint overlay, a parts catalog, material, labor and equipment breakdowns, team access controls, bid management and Excel export, on a phone, Mac or PC. All features are on every plan, and the FAQ states that only the month-to-month plan needs no contract. Falls short on: the pages name no assemblies with logic and no proposal output beyond the estimate and the export. A second estimator means a call for pricing.

Kreo: volume and formwork measurement from $100 a user

Best for: small estimating teams that want 2D and 3D takeoff with a shared cost database at the lowest annual seat price here. Price: Essential is $100 a user a month billed annually ($1,200 a year) and Pro $175 ($2,100); Business is $250 a user a month billed annually with 5 seats included, billed at $15,000 a year. A 7-day trial is offered (kreo.net/pricing, checked 13 November 2026).

Strengths: the concrete page describes slabs, columns, footings and walls measured into estimates and quotes, ready-made concrete cost templates, concrete volume, formwork area and a precast elements calculator. Essential includes area, length, volume and count measurement, live-linked estimates with custom assemblies, a shared company cost database and Excel import and export. Pro adds one-click measurement, symbol counting and AI takeoff of rooms, walls, doors and windows. Falls short on: the FAQ states that every plan is billed annually and there is no monthly subscription; the monthly figures are the annual price divided by 12. The AI takeoff on Pro is aimed at rooms and openings rather than foundations. Business includes 5 seats and is billed at $15,000 a year.

An estimator built for concrete trades: The EDGE

Best for: commercial concrete subcontractors whose labor varies by element size and who want takeoff, estimate, vendor quotes and proposal in one system. Price: not published; the concrete page offers a demo (checked 13 November 2026).

Strengths: Smart Labor adjusts forming, pouring and finishing labor by task complexity, so a 12-foot footing carries a different rate from a 6-foot one. A universal edit to depths, widths, rebar or labor recalculates the estimate in cubic yards, linear feet, square feet and tons. The page reports a World of Concrete Innovative Product Award for its concrete database. The homepage describes a built-in proposal writer, supplier price requests from inside the software, and EDGE On Site for tracking production against the estimate in the field. Falls short on: no published price or trial, and the EDGE pages name no CRM.

Map-based estimating for paving and flatwork: OneCrew

Best for: asphalt and concrete paving contractors who measure parking lots and driveways from maps and send a proposal the same day. Price: not published; getonecrew.com/pricing returned a 404 on 13 November 2026.

Strengths: the homepage states that OneCrew works only with asphalt and concrete businesses and describes mapping, estimates and proposals, configurable estimates, proposal generation and drag-and-drop scheduling built for paving. Falls short on: no price or trial, and the pages describe map measurement rather than plan takeoff, so structural concrete from drawings is not a use they describe. OneCrew also publishes its own ranked list of concrete estimating software, which places OneCrew first.

Concrete estimates on HubSpot deals: FieldRanger

Best for: residential and light commercial concrete contractors (driveways, patios, foundations for remodels) whose leads and estimates live in HubSpot. Price: per technician, on the FieldRanger pricing page; Start free trial runs 14 days with no card.

Strengths: an estimate is built from the HubSpot deal or contact record, or in FieldRanger and kept tied to the deal, with the estimating software described on the features page. Estimates and agreements go out for signature through PandaDoc. A won deal becomes a job with its context carried over, and the dispatcher drags it onto the calendar. Clock-ins record where the assigned finisher was, materials used on each job are logged for job costing, and before and after photos and the customer's signature sit on the work order. The invoice is generated from the completed work order and syncs with QuickBooks. The HubSpot field service page sets out the records.

Falls short on: FieldRanger is not takeoff software, so yardage and rebar come from the estimator's own sheet. There is no weather feed for pour days, and a pour followed by finishing and saw-cutting is one job per day, because multi-day jobs are not built. Progress billing and retainage are not built, which rules FieldRanger out for billing a general contractor on a subcontract. A subcontractor bidding commercial work from plans is better served by STACK, PlanSwift, eTakeoff or The EDGE.

Estimating software for concrete subcontractors bidding to general contractors

A concrete subcontractor bids to several general contractors on the same project, each with its own bid form, and a revised set can arrive days before the deadline. Four capabilities separate the tools on that work. Drawing comparison catches the revised slab thickness: STACK, PlanSwift, eTakeoff, Square Takeoff and Kreo all list overlays or version comparison. Phased quantities split a building into pours: eTakeoff Premier lists work zones and phases. Labor that varies with the element is The EDGE's Smart Labor. A scope letter with inclusions and exclusions comes from STACK Pro's native proposals and The EDGE's proposal writer, while PlanSwift and eTakeoff hand the quantities to Excel.

Once the subcontract is signed, the time cards change shape: hours are coded to the pour, and some public jobs require certified payroll. Those tools are compared in best construction time tracking app.

Takeoff, assemblies and proposals by tool

Where each capability is stated, from vendor pages checked 13 November 2026
CapabilityWhere it is stated
Cubic yards and rebar from the takeoffSTACK, every paid plan; PlanSwift, assemblies; Square Takeoff, slabs, footers, walls and rebar; The EDGE, yards and tons of rebar; Kreo, volume, formwork and slab rebar; eTakeoff, not stated on the pricing page
AssembliesPlanSwift Essential, pre-built; STACK Premium and Pro; eTakeoff Premier, with logic; Kreo Essential, custom; The EDGE, preloaded trade data; Square Takeoff, parts catalog
Drawing comparisonSTACK Premium; PlanSwift; eTakeoff, both plans; Square Takeoff; Kreo Essential
Proposal outputSTACK Pro, native proposals; The EDGE, proposal writer; OneCrew, proposal generation; Kreo, quotes; PlanSwift, eTakeoff and Square Takeoff, Excel export; FieldRanger, estimates on the HubSpot deal
After the bidThe EDGE, production tracking with EDGE On Site; OneCrew, scheduling; FieldRanger, scheduling, time, job costing and invoicing; the others, not stated

Read down the last row, only three of the eight carry the bid into the field. The takeoff tools end at the quantity or the proposal, which suits a subcontractor with a separate project system and leaves a residential contractor typing the job in twice.

Year-one cost of one seat with assemblies and rebar

The sample prices one estimator for a year on the lowest plan that lists assemblies or a parts catalog. It is arithmetic on list prices, not a quote, and add-ons are excluded.

Sample year-one cost for one estimator, computed from vendor prices checked 13 November 2026
Tool and planBasisYear one
Kreo Essential$100 a month billed annually; custom assemblies$1,200
eTakeoff PremierAnnual; assemblies with logic, zones and phases$1,495
Square Takeoff, annualEvery feature; parts catalog$1,699
PlanSwift EssentialAnnual seat; pre-built assemblies$2,000
eTakeoff Premier with Togal.aiAdds AI takeoff$3,295
STACK Premium, annual$299 a month; item and assembly library$3,588
STACK Pro, annual$349 a month; adds native proposals$4,188
STACK Pro, paid monthly$399 a month on the 12-month term$4,788
The EDGE, OneCrewNot publishedQuote
FieldRangerPer technician; no takeoffSee [pricing](/pricing)

The seat cost spans $1,200 to $4,788. The cheaper tools stop at quantities and an estimate, while STACK Pro and The EDGE carry the same measurement into a proposal a general contractor can read.

Footing-and-slab bid test for concrete estimating software

  1. Take one real set with a spread footing schedule, a 4-inch slab on grade and a thickened edge, and the yardage from the last bid on it.
  2. Run the takeoff in each trial and record the cubic yards, the linear feet of form and the tons of rebar.
  3. Apply the same waste factor and labor rates, and price the pump and the finish.
  4. Load the revised sheet with a changed slab thickness and time how long the estimate takes to update.
  5. Produce the proposal or the Excel export with inclusions and exclusions.
  6. Verify: the yardage in each tool falls within 2% of the hand count, and the revised slab changes the yards, the concrete cost and the total in the proposal.

Frequently asked questions

What is the best estimating software for concrete construction?

For commercial subcontractors bidding from plans, STACK, PlanSwift, eTakeoff or The EDGE. For small crews on a budget, Square Takeoff or Kreo. For paving and flatwork measured from maps, OneCrew. For residential contractors selling through HubSpot, FieldRanger, on vendor pages checked 13 November 2026.

What is the best estimating software for concrete subcontractors?

A subcontractor bidding to general contractors needs drawing comparison, phased quantities and a proposal: STACK Pro and The EDGE produce proposals from the takeoff, eTakeoff Premier splits quantities by work zone and phase, and The EDGE varies labor by element size.

What is the best concrete estimating software for a small contractor?

Kreo Essential costs $1,200 a year with custom assemblies, and Square Takeoff costs $249 a month with no contract or $1,699 a year, with every feature on each plan. STACK's free version allows 1 active project a month.

How much does concrete estimating software cost?

Published seat prices checked on 13 November 2026 run from $795 a year for eTakeoff Advanced to $399 a month for STACK Pro paid monthly on a 12-month term. PlanSwift costs $2,000 a year, and The EDGE and OneCrew quote.

Can estimating software calculate rebar?

STACK accounts for rebar as the estimator measures, PlanSwift uses assemblies for rebar and membranes, Square Takeoff calculates rebar with slabs and walls, and The EDGE reports tons of rebar.

Does concrete estimating software work with HubSpot?

FieldRanger builds estimates on the HubSpot deal and turns a won deal into a job. STACK's pricing FAQ states integrations with CRM systems without naming one; PlanSwift, eTakeoff, Kreo, Square Takeoff, The EDGE and OneCrew name no HubSpot connection on the pages checked.

Concrete estimating vendor pages and check dates

All pages below were read with a plain request on 13 November 2026.

Depth separates these tools. STACK, PlanSwift, eTakeoff and The EDGE carry depth, rebar and labor from one measurement into the bid, and a concrete bid is won or lost on yards and tons. A concrete contractor selling driveways and patios through HubSpot can run the estimate, the pour day and the invoice on one deal with Start free trial on pricing.

Run field service on HubSpot with FieldRanger

Estimates with e-signature, scheduling and dispatch, a technician mobile app and invoicing, synced to the HubSpot deals and contacts the business already keeps.

Book a demo