Guide

Commercial Painting Supplies:Coatings by Substrate and MPI Number, Sundries, Scissor Lifts, Dust Containment and a Priced Tenant Fit-Out Order

Commercial painting supplies: primers, block fillers and DTM enamels by substrate and MPI number, sundries, lift rental, dust barriers and a priced order.

By Published Updated

14 min read

Commercial painting supplies are the coatings, sundries, access equipment and containment a commercial repaint or new-construction job consumes: primers, block fillers, finish coats and direct-to-metal enamels chosen by substrate and by the project specification; 18-inch roller covers, strainers and patching; a rented scissor lift; and flame-retardant dust barriers for occupied buildings.

A commercial supply order goes wrong at the specification, not at the counter. New block gets one coat of finish where the spec called for a block filler first, and the second coat shows every pore. A door frame is painted with a direct-to-metal enamel whose label says no primer is needed, while the paint schedule lists a metal primer. A standard plastic zip door goes up in a corridor that stays open to tenants. A scissor lift is rented by the day for two weeks. FieldRanger is painting contractor software that runs inside HubSpot, and this guide covers the supplies a commercial job draws on. It sets out how repaint and new-construction scopes differ and how a paint schedule names products by MPI number. It then prices coatings by substrate, sundries, lift rental and containment from maker and distributor pages read on November 13, 2026. A priced supply order for a sample tenant fit-out, the common ordering errors, a checklist and the job records follow.

Four terms carry the page. A substrate is the surface being coated: gypsum board, concrete masonry units (CMU), steel or concrete. An MPI number identifies a coating category in the Master Painters Institute's performance standards, such as MPI 4 for latex block filler. Dry film thickness (DFT) is the thickness of a coat after it cures, in mils. Practical coverage is the area one gallon covers at the recommended film thickness, after an allowance for material lost in application.

Commercial painting supplies for repaint and new-construction scopes

The scope decides the supply list before the colour does. A repaint coats surfaces that have been painted before; new construction coats bare surfaces that absorb more and need primers and fillers that a repaint does not.

How the commercial scope changes the supply list
Supply lineCommercial repaintNew construction or tenant fit-out
Gypsum boardSpot-prime patches, then finish coatsA latex primer sealer over every board, then finish coats
Concrete masonry unitsA primer coat, then finish coats; no block fillerBlock filler at 75 to 125 sq ft a gallon, then finish coats
Steel door framesScuff-sand and finishPrimer or a direct-to-metal system, as the schedule states
ContainmentDust barriers and zip doors around occupied areasFloor protection on finished floors; barriers where other trades work
AccessLifts and ladders worked around tenants' hoursLifts shared with other trades on the general contractor's schedule

Residential painting kit, from brushes to the lead-safe kit, is priced in the guide on what equipment is needed to start a painting business. This page keeps to commercial jobs.

Paint schedules and MPI product numbers

A commercial job is supplied from its paint schedule. The Unified Facilities Guide Specification for architectural paints and coatings, revised in August 2026, names a coating system for each substrate by MPI number (UFGS 09 90 00, via WBDG). Its tables separate new surfaces from "existing, previously painted" ones. The systems differ:

  • New CMU takes MPI 4 block filler, then two coats of high-performance latex such as MPI 139 eggshell, for a system DFT of 11 mils.
  • Previously painted CMU takes no filler: a primer coat of the finish latex and two more coats, for 4.5 mils.
  • New gypsum board takes MPI 50 latex primer sealer, then two finish coats, for 4 mils.
  • Interior steel takes a metal primer, MPI 76 in the specification's tables, then two finish coats, for 5 mils.

The specification is written for federal work, and private architects' schedules vary in wording. The products behind the numbers come from one list. MPI tests products against its performance standards and lists those that pass on its Approved Product List, "updated monthly" (Master Painters Institute, read November 13, 2026). MPI describes the listed products as the ones "specified on Commercial and Government projects". An estimator checks each product against the schedule's MPI number before ordering. A substitute that is not on the list is a submittal the architect can reject.

Coatings by substrate: gypsum board, block and steel frames

The coatings below are priced from distributor pages that showed a price on November 13, 2026. Benjamin Moore's own commercial pages, for example its Ultra Spec 500 eggshell, list coverage but showed "Not Available" in place of a price. A maker's coverage figure and a distributor's price can therefore come from different pages.

Commercial coatings by substrate, distributor prices read November 13, 2026
Substrate and coatProductPriceCoverage statedSource
Gypsum board, primerSheetrock First Coat drywall primer, 5 gal$89.99300 to 500 sq ft a gallon[Do it Best](https://www.doitbest.com/product/795232/sheetrock-first-coat-drywall-primer-5-gal-795232/)
Walls and CMU, finishValspar Pro-Hide Gold Ultra Zero VOC eggshell, 5 gal$179.99400 sq ft a gallon[Do it Best](https://www.doitbest.com/product/771552/valspar-pro-hide-gold-ultra-zero-voc-latex-eggshell-interior-wall-paint-super-one-coat-white-5-gal-771552/)
New CMU, fillerDo it Best latex masonry block filler, 5 gal$99.9975 to 125 sq ft a gallon on block[Do it Best](https://www.doitbest.com/product/787523/do-it-best-latex-masonry-block-filler-5-gal-787523/)
Steel frames, finishRust-Oleum 3800 System DTM acrylic enamel, gloss black, 1 gal$54.76150 to 270 sq ft a gallon at 2 to 3 mils[Whitehead Industrial](https://whiteheadindustrial.com/high-performance-3800-system-dtm-acrylic-enamel-gloss-black-1-gallon-no-314387); [Rust-Oleum data sheet RO-127, via Direct Tools](https://www.directools.com/documents/all/Rust_Oleum_315506_Catalog.pdf)

Do it Best's listings state that in-store prices may vary. The Pro-Hide listing describes the paint as "ideal for residential/commercial repaints and new construction" and "MPI approved for gloss levels 1-5". The block filler listing excludes block "where moisture or high humidity is a problem, such as showers or car washes".

The direct-to-metal line needs one caution. Whitehead's listing describes the 3800 System as a direct-to-metal coating with "no primer required". The Rust-Oleum data sheet gives a recommended DFT of 2.0 to 3.0 mils a coat. The UFGS tables still list a primer under interior steel. The label describes what the product can do; the schedule decides what the job gets. A two-coat DTM system goes on only where the architect has accepted it.

Coverage arithmetic from product data

Gallons follow from area, coats and the stated coverage. The estimator divides the area by the coverage, multiplies by the coats, and rounds up to whole pails.

The low end of each range is the safe figure on new work, because bare surfaces absorb more. The block filler shows how much the range matters. On 1,800 square feet of new block, the filler takes 24 gallons at 75 square feet a gallon and 14.4 gallons at 125. That is five pails or three, and $199.98 between them at $99.99 a pail. The fields that carry these quantities into a bid are set out in the painting estimate template.

Commercial sundries: wide covers, grids, strainers, patching and tape

Commercial walls are long and mostly unbroken, so the sundries scale up. Prices below are from Painter's Solutions, a paint supply retailer, read on November 13, 2026.

Commercial sundries at Painter's Solutions (prices read November 13, 2026)
ItemPriceUse on a commercial job
[Wooster RR642 18-inch Pro/Doo-Z 3/8-inch nap roller cover, 6-pack](https://painterssolutions.com/products/wooster-rr642-18-pro-doo-z-3-8-nap-roller-cover-6-pack)$50.50Rolling long corridor and office walls from a 5-gallon pail
[Wooster F0001 5-gallon Acme Deluxe grid, 12-pack](https://painterssolutions.com/products/wooster-f0001-5g-acme-deluxe-grid)$21.50Rolling out of the pail instead of a tray
[Trimaco 11513/25 5-gallon elastic top strainer, 25-pack](https://painterssolutions.com/products/9018038)$25.50Straining pails before they feed a sprayer
[Crawfords 31901 spackling paste, 1 gallon](https://painterssolutions.com/products/crawfords-31901-1-gallon-spackling-paste)$69.90Patching anchor holes and dents in occupied offices
[Shurtape FrogTape Pro Grade 1.88-inch blue painter's tape, 3-pack](https://painterssolutions.com/products/shurtape-104957-48mm-x-55m-1-88-x-60yd-blue-frogtape-pro-grade-painters-tape-3-pack)$19.99Masking frames, glazing and ceiling grid
[Trimaco 12360 36-inch by 120-foot X-Paper HD builders paper, 20-pack](https://painterssolutions.com/products/trimaco-12360-36-x-120-x-paper-hd-builders-paper-20-pack)$525.00Protecting finished floors in a fit-out

The 18-inch cover replaces the residential 9-inch one on open wall. It is loaded from a 5-gallon pail with a grid rather than from a tray, so the grid and the pail-size strainer sit on the same order.

Access equipment: scissor lifts and towable booms

Commercial ceilings, soffits and stairwells put much of the work above ladder height, where a lift replaces the ladder. Grand Rental Station in Hudson and Pelham, New Hampshire lists a 19-foot Haulotte Optimum 1931 electric scissor lift at $195.00 a day and $455.00 a week (Grand Rental Station, 19-foot electric scissor lift, read November 13, 2026). Its platform carries 507 pounds: two people and tools. The listed price is for customer pickup, and delivery is quoted separately. The same page lists a 43-foot tow-behind lift at $280.00 a day and $1,120.00 a week.

The weekly rate decides how a lift is rented. Three days at $195.00 cost $585.00, more than the $455.00 week, so a lift needed for three days or longer is rented by the week.

The two machines fall under different OSHA rules, and the rule changes the supply list. OSHA's interpretation states that "scissor lifts are not aerial lifts" and are treated as scaffolds (OSHA standard interpretation, August 1, 2000). The scaffold rules do not require employees "to be tied-off when working from scissor lifts that have properly maintained guardrails". A boom lift is an aerial lift. OSHA's aerial lift standard requires that "a body belt shall be worn and a lanyard attached to the boom or basket" (29 CFR 1926.453). A note to that paragraph states that body belts have not been acceptable as part of a personal fall arrest system since January 1, 1998. A job that rents the tow-behind boom therefore adds a harness and lanyard for each painter in the basket.

Dust containment in occupied commercial buildings

A commercial repaint worked while the building stays open needs containment to keep dust and overspray inside the work area. ZipWall lists its ZipWall 12 four-pack of spring-loaded poles at $325.55 (ZipWall, ZipWall 12 4-Pack, read November 13, 2026). The poles telescope to 12 feet and hold a barrier up to 30 feet wide.

The zip door is the item where the commercial version differs. ZipWall lists its ZipDoor Commercial Door Kit at $49.45 (ZipWall, ZipDoor Commercial Door Kit, read November 13, 2026). The kit is made of 4 mil flame-retardant sheeting and fits a door up to 4.5 by 8 feet. The same page states that "the standard door is not flame retardant". Painter's Solutions listed the same commercial kit at $41.99 on the same day, so the maker's price and a distributor's price differ by $7.46 a door.

Containment rules also follow the building's age. The EPA's lead renovation rule applies to housing and to "child-occupied facilities (such as schools and child care centers) built before 1978" (EPA, RRP program, updated November 12, 2026). A commercial repaint of an older school or day care therefore carries the lead-safe work practices. The firm certification behind them is covered in how to start a painting business.

Sample tenant fit-out supply order for Nashua, New Hampshire

The job is hypothetical: a painting contractor supplying the interior of a tenant fit-out in Nashua, New Hampshire. The scope is 8,000 square feet of new gypsum board, 1,800 square feet of new CMU in a stairwell and 30 hollow metal door frames at 18 square feet each. The schedule is assumed to accept a two-coat DTM system on the frames. Areas, frame size and sundry quantities are sample inputs. Prices and coverage are from the pages cited above, at the low end of each coverage range.

Sample commercial painting supply order, Nashua, New Hampshire (sample inputs labelled; prices read November 13, 2026)
LineBasisQuantityUnit priceLine total
Drywall primer, 5 gal8,000 sq ft ÷ 300 = 26.7 gal6 pails$89.99$539.94
Eggshell finish, 5 galWalls 16,000 ÷ 400 = 40 gal; CMU 3,600 ÷ 400 = 9 gal10 pails$179.99$1,799.90
Block filler, 5 gal1,800 sq ft ÷ 75 = 24 gal5 pails$99.99$499.95
DTM enamel, 1 gal30 frames × 18 sq ft × 2 coats ÷ 150 = 7.2 gal8 gallons$54.76$438.08
18-inch roller covers, 6-packSample quantity2$50.50$101.00
5-gallon grids, 12-packSample quantity1$21.50$21.50
5-gallon strainers, 25-packSample quantity1$25.50$25.50
Spackling paste, 1 galSample quantity2$69.90$139.80
FrogTape Pro Grade, 3-packSample quantity4$19.99$79.96
ZipWall 12 four-packMaker's price1$325.55$325.55
ZipDoor Commercial kitMaker's price2$49.45$98.90
19-foot scissor lift, weeklyGrand Rental Station, pickup2 weeks$455.00$910.00
TotalSum of the lines above$4,980.08

Coatings are $3,277.87, or 65.8 percent of the order. The order covers 9,800 square feet of wall at $0.51 a square foot before labour, delivery and tax. The lift by the week costs $910.00 against $1,950.00 for ten working days at the daily rate. Had the stairwell block been painted before, the UFGS repaint system would drop the $499.95 block filler line. A primer coat of the finish latex would take its place.

Commercial supply errors and their mechanisms

Each error below has a symptom on the wall, a cause in the order, and a fix in the estimate.

  • Pores showing through the finish on new block. The order carried finish paint only; new CMU needed MPI 4 filler first. The fix is a filler line on every new-block area in the estimate, priced at the low end of its coverage.
  • A rejected product submittal. A substitute coating was ordered that is not on the MPI list for the number in the schedule. The fix is to check the Approved Product List before the order, not after delivery.
  • A primer dispute on steel frames. The DTM label said no primer was needed; the schedule listed one. The fix is a written acceptance from the architect, or the primer on the order.
  • A rental bill above the plan. A lift kept for two weeks was billed at the daily rate. The fix is a weekly rental for any lift needed three days or longer.
  • Short paint on the last day. Coverage was taken from the top of the range on porous new board. The fix is the low end of the range for new surfaces, and a pail count rounded up.

Commercial painting supply checklist

  1. Read the paint schedule and list each substrate, its new or existing condition and its MPI system.
  2. Check every product against the MPI Approved Product List for its number before ordering.
  3. Take each area from the drawings and divide by the low end of the stated coverage, times the coats; round up to whole pails.
  4. Add block filler for new CMU only, and a primer line for steel unless the architect has accepted a DTM system in writing.
  5. Order 18-inch covers, grids and pail strainers in proportion to the wall area.
  6. Price containment as commercial zip doors in any area that stays open to occupants, and ZipWall poles long enough for the ceiling height.
  7. Rent lifts by the week for any lift needed three days or more, and add a harness and lanyard for each painter in a boom basket.
  8. Check the build year of schools and day cares before the bid, for the lead-safe rule.
  9. Verify after delivery: count pails and gallons against the order, and compare product names and MPI numbers on the labels with the submittal the architect approved.

Materials, stock and job costs in FieldRanger

FieldRanger records what each commercial job consumed against the job and the HubSpot deal it came from. Materials tracking logs the parts and materials used on each job for job costing, so the pails and gallons above are recorded against the job that used them. With warehouse-specific inventory checkout, a painter checks materials out of a specific warehouse, so stock is counted where it sits. Inventory alerts give low-stock warnings and reorder reminders. Each painter's truck can also be its own stock location. Equipment assignment assigns owned equipment such as the ZipWall poles to jobs and technicians; a rented lift is the rental company's asset and sits outside it.

The estimate is built from the HubSpot deal or contact record, or in FieldRanger and kept tied to its deal. A won deal becomes a job with its context carried over. Commercial work raises two limits. Multi-day jobs are not built, so a two-week fit-out is one job for each day, and each job can carry that day's crew of painters. Progress billing and retainage are not built either, so pay applications to a general contractor are prepared outside FieldRanger. The inventory management page covers stock by warehouse, and plans are on pricing, where Start free trial runs 14 days with no card.

Frequently asked questions

What are commercial painting supplies?

The coatings, sundries, access equipment and containment a commercial job uses: primers, block fillers, finish coats and direct-to-metal enamels chosen by substrate and specification; 18-inch roller covers, grids, strainers, patching and tape; rented scissor or boom lifts; and flame-retardant dust barriers for occupied buildings.

What primer is used on new drywall in commercial painting?

A latex primer sealer, MPI 50 in the UFGS 09 90 00 tables, before two finish coats. Do it Best listed Sheetrock First Coat at $89.99 for 5 gallons on November 13, 2026, with stated coverage of 300 to 500 square feet a gallon.

Does previously painted concrete block need block filler?

Not under the UFGS 09 90 00 tables, which list block filler for new CMU and a primer coat plus two finish coats for existing, previously painted block. New block takes MPI 4 filler, stated at 75 to 125 square feet a gallon on the Do it Best filler listed at $99.99 for 5 gallons.

Is a harness needed on a scissor lift for painting?

OSHA's 2000 interpretation treats scissor lifts as scaffolds and states that employees need not be tied off on a scissor lift with properly maintained guardrails. A boom lift is an aerial lift, and 29 CFR 1926.453 requires a body belt and a lanyard attached to the boom or basket.

How much does it cost to rent a scissor lift for a painting job?

Grand Rental Station in Hudson and Pelham, New Hampshire listed a 19-foot electric scissor lift at $195.00 a day and $455.00 a week for pickup on November 13, 2026. At those rates, three days cost more than a week.

What dust containment is used for commercial painting?

Spring-loaded barrier poles and zipper doors. ZipWall listed its 12-foot four-pole kit at $325.55 and its flame-retardant ZipDoor Commercial kit at $49.45, and states that its standard door is not flame retardant.

The Nashua order spends two-thirds of its $4,980.08 on coatings, and the one line that the schedule's new-or-existing column decides, $499.95 of block filler, is the easiest to leave off.

Run field service on HubSpot with FieldRanger

Estimates with e-signature, scheduling and dispatch, a technician mobile app and invoicing, synced to the HubSpot deals and contacts the business already keeps.

Book a demo