Guide

How to Estimate Residential Electrical Work:Take-Off from Plans, Per-Device and Per-Opening Pricing, Labor Hours, Material Lists, Madison Permit Fees and 2023 NEC Outlet Rules

How to estimate residential electrical work: plan take-off, per-device and per-opening pricing, labor hours, material lists, Madison permit fees and NEC rules.

By Published Updated

12 min read

How to estimate residential electrical work, in order: count every device on the plans by symbol and room, check the counts against the outlet rules of the adopted code, assign labor hours to each device and each circuit, build the material list from the same counts, add the permit fee from the local schedule, then price overhead and margin.

An electrical estimate built any other way is short in the rooms nobody counted. A hallway over 10 feet long gets no receptacle and the inspector writes it up. A per-opening price from a receptacle-heavy job is applied to a basement full of recessed lights. A cable order is guessed by the roll and comes up two runs short on the last afternoon. FieldRanger makes electrical contractor software that runs inside HubSpot, and this page is one of its pricing and quoting guides. It sets out the take-off from plans, the outlet counts in the 2023 National Electrical Code with their source, the two ways of pricing devices, labor hours, the material list, Madison, Wisconsin's permit fees, and one basement finish estimated with the arithmetic shown.

Five terms carry the method. A take-off is the count of every item on the plans, by type and room. An opening is a box in the wall or ceiling: a receptacle, a switch, a luminaire or a smoke alarm. Per-device pricing sets a price for each type of device; per-opening pricing sets one average price for any opening. A labor unit is the hours allowed to install one item, from rough-in to trim-out. A home run is the cable from the first box on a circuit back to the panel.

Take-off from plans: symbols, rooms and runs

The take-off works room by room, and the plan legend is read before the first count. Each symbol type is counted on its own pass: receptacles, then switches, then luminaires, then dedicated circuits and special devices. A count made in one pass across all symbols loses items where symbols overlap on a dense plan.

Three counts are recorded for every room:

  1. Devices by type. Duplex receptacles, GFCI receptacles, single-pole and three-way switches, recessed and surface luminaires, fans and smoke alarms.
  2. Circuits. Each circuit on the panel schedule, or each circuit the estimator assigns where the plan gives none.
  3. Run lengths. The distance from each box to the next on the circuit, and from the first box to the panel, scaled from the plan and increased for vertical drops and routing around framing.

Where there are no plans, as on a remodel without drawings, the estimator draws a sketch with dimensions on site and takes off from the sketch. The electrical estimate guide covers the lines the finished estimate carries; this page is the method that fills them.

Outlet counts from the 2023 National Electrical Code

The code sets a minimum count in each room, and the take-off is checked against it before pricing. The rules below are from section 210.52 of the 2023 NEC as set out in Mike Holt Enterprises' Understanding the 2023 National Electrical Code, Volume 1, 2nd printing, read November 13, 2026:

  • General wall space. Receptacles are placed so that "no point along the floor line of any wall is more than 6 ft" from one, and any wall space 2 ft or more wide counts.
  • Kitchen countertops. No point along a countertop wall space may be more than 2 ft from a receptacle, and countertop receptacles are supplied by no fewer than two 20A, 120V small-appliance branch circuits [210.11(C)(1)].
  • Bathrooms. At least one receptacle "within 3 ft of the outside edge of each bathroom sink".
  • Outdoors. One- and two-family dwellings carry one receptacle at the front and one at the back, readily accessible from grade and not more than 6½ ft above it.
  • Laundry, garage and basement. One receptacle where laundry equipment is intended, one in each vehicle bay of a garage, and one in each unfinished portion of a basement.
  • Hallways and foyers. At least one receptacle in each hallway 10 ft or more long, and a receptacle on each wall space 3 ft or wider in a foyer over 60 sq ft.

The edition depends on the state. Wisconsin's new electrical code, which "adopts 2023 National Electrical Code (NEC) standards" with "specific changes and omissions to ensure it conforms to Wisconsin statutes", took effect September 1, 2026, replacing a code based on the 2017 NEC (EC&M, Wisconsin implements new electrical safety code, June 30, 2026). A Wisconsin estimate for plans submitted after that date is checked against the 2023 rules and the state's changes to them, not against the code the company priced to last year.

Per-device pricing and per-opening pricing

Both methods produce a price from the take-off; they differ in how much of the take-off survives into the price.

Per-device pricing keeps each device type separate. A recessed light carries its own labor hours and material, a switch its own, and the estimate totals them. The price follows the mix of devices on the plan.

Per-opening pricing divides a past job's total by its openings and applies that average to the next job. It is fast and easy to explain to a homeowner, and it holds only while the next job has the same mix. The sample below shows the size of the error when the mix changes.

Labor hours per device and the loaded rate

Labor hours come from the company's own completed jobs: clocked hours divided by devices installed, by device type and by job type. Published labor unit manuals exist and give starting values, but the company's records replace them once enough jobs are clocked, because they include the company's own travel, rough-in method and inspection delays.

The hours are priced at a loaded rate. In the Madison metro, electricians earned a median of $37.71 an hour and $48.32 at the 75th percentile in BLS 2025 wage data (O\*NET OnLine, Wisconsin wages for 47-2111.00, read November 13, 2026). The employer adds 6.2 percent Social Security and 1.45 percent Medicare (IRS Topic 751, updated November 9, 2026), and the company adds its own benefits and workers' compensation. Hours that cannot be billed, such as supply runs and the office, are spread across billable hours.

Material lists from the take-off

The material list is built from the same counts as the labor, so the two cannot disagree. Each device type brings a fixed set of parts:

  • Boxes. One per opening, new-work boxes where framing is open and old-work boxes where it is not.
  • Devices and plates. One device and one cover plate per opening, with GFCI devices counted separately.
  • Luminaires. Counted by type, and marked "by owner" where the homeowner supplies the fixture, so that only the box and labor are priced.
  • Cable. Run lengths from the take-off, totalled by cable type and gauge, plus a stated allowance for drops and waste, then rounded up to the roll size sold.
  • Breakers and connectors. One breaker per circuit, of the type the code requires for that circuit, plus connectors, staples and wire nuts allowed per opening.

Material prices come from the supplier's written quote on the day of the estimate, with the quote date written on the estimate so that a later price change is visible. A markup is applied to material at a stated percentage.

Madison permit fees for existing dwellings and new homes

The permit fee is a line on the estimate, taken from the jurisdiction's schedule on the day of pricing. The City of Madison's Building Inspection fee page lists these inspection fees (City of Madison, Building Inspection Fees, read November 13, 2026):

City of Madison electrical inspection fees (read November 13, 2026)
WorkFee
New or altered electrical openings, existing buildings$25.00 for the first ten openings, $1.00 for each additional opening
Electric service replacement$50.00 per service panel
New one- and two-family buildings (Group 1), electrical$0.09 per square foot, minimum $25.00

The page instructs that all fees are rounded up to the next highest dollar. Its fee table does not define an opening; the sample below counts each receptacle, switch, luminaire, fan and smoke alarm box as one, and the count is confirmed with the inspector when the permit is filed. Madison's schedule prices the alteration permit by the same unit the per-opening estimate uses, so the take-off count feeds the permit line directly.

Sample estimate for a basement finish in Madison, Wisconsin

The job is hypothetical: a basement finish in an existing single-family house in Madison, with a family room, a bedroom, a bathroom, a hallway and an unfinished mechanical room. Device counts, labor hours, material costs, the markup, the billable rate and run lengths are sample inputs, labelled as such. The wage, tax rates, code rules and permit fees come from the sources above.

The code check. The plan shows 11 receptacles in the family room, 6 in the bedroom, one GFCI receptacle beside the bathroom sink, one in the 12-foot hallway and one in the mechanical room (sample). The hallway is over 10 feet, so it needs one; the mechanical room stays unfinished, so it needs one; the bathroom receptacle sits within 3 feet of the sink edge. The take-off passes before it is priced.

Sample take-off and per-device price at $128 a billable hour (sample inputs labelled)
Device (sample count)Labor hours each (sample)LaborMaterial each with 25% markup (sample)Price eachLine total
Receptacle (19)0.45$57.60$17.50$75.10$1,426.90
Bathroom GFCI receptacle (1)0.55$70.40$42.50$112.90$112.90
Single-pole switch (7)0.40$51.20$15.00$66.20$463.40
Three-way switch (2)0.55$70.40$22.50$92.90$185.80
Recessed light, canless (10)0.60$76.80$47.50$124.30$1,243.00
Surface or vanity light box, fixture by owner (4)0.50$64.00$12.50$76.50$306.00
Bath exhaust fan (1)1.25$160.00$118.75$278.75$278.75
Smoke alarm, hardwired (2)0.50$64.00$52.50$116.50$233.00
Six circuits: home runs, breakers, terminations7.8 hours$998.40$525.00$1,523.40
Permit: 46 openings$25.00 + 36 × $1.00$61.00
Total31.05 hours$5,834.15

The billable rate. The $128 rate is built from the Madison median: $37.71 plus 7.65 percent payroll taxes and 18 percent benefits and workers' compensation (sample) is $47.38 an hour. Paid for 2,080 hours and billing 1,560 (sample), the electrician costs $63.18 per billable hour, before $45.00 of overhead (sample) and profit.

The cable order. Forty-six openings at 18 feet each and six home runs at 40 feet (sample run lengths) total 1,068 feet, which is five 250-foot rolls before the split between 14-gauge and 12-gauge circuits.

Per-opening price against per-device price. The job totals $5,834.15 across 46 openings, or $126.83 an opening. Apply that average to a second basement with the same 46 openings and six circuits but a different mix:

The same 46-opening average applied to two other device mixes (sample inputs labelled)
Mix (sample)Per-device pricePer-opening price at $126.83Difference
This job: 20 receptacles, 9 switches, 14 lights, 1 fan, 2 alarms$5,834.15$5,834.15$0.00
30 recessed lights, 16 switches$6,372.60$5,834.15$538.45 under-priced
30 receptacles, 16 switches$4,896.60$5,834.15$937.55 over-priced

The over-priced bid loses the job to a competitor; the under-priced one wins it and gives away $538.45. A per-opening figure is therefore quoted only with the device mix it came from.

Take-off errors: symptom, cause and correction

Each entry pairs a symptom on the job with the take-off step that produced it.

  • Inspector's correction for a missing receptacle. The room was counted, the code check was not; the hallway or unfinished area minimum was missed. The fix lives in the take-off checklist: a code check per room before pricing.
  • Hours over the estimate on lighting-heavy jobs. A per-opening average from a receptacle-heavy job was applied. The fix is per-device pricing, or a per-opening price quoted with its mix.
  • Cable short on the last day. Run lengths were guessed by the roll rather than totalled from the take-off. The fix is a length per opening and per home run, totalled and rounded up to the roll.
  • Permit fee wrong on the estimate. The fee was copied from an older schedule or a different jurisdiction. The fix is the fee page read on the day of the estimate, with its date on the line.

Residential electrical estimating checklist

  1. The plan legend is read and each symbol type is counted on its own pass, room by room.
  2. Every room's count is checked against the adopted code's minimums, in the edition the state enforces for the permit date.
  3. Circuits are listed, with the code-required breaker type for each.
  4. Run lengths are scaled from the plan for every box and home run, with a stated allowance.
  5. Labor hours per device come from the company's clocked jobs, by device type.
  6. The billable rate is built from the loaded wage, the paid-to-billable ratio and overhead.
  7. The material list is generated from the same counts as the labor, priced from a dated supplier quote.
  8. The permit fee is read from the local schedule on the day of the estimate and counted by the schedule's own unit.
  9. Any per-opening price is shown with the device mix behind it.
  10. Verify on completion: compare clocked hours per device type and cable used with the estimate, and update the labor units and the per-opening length.

Estimates, signatures and job records in FieldRanger

FieldRanger keeps the estimate on the HubSpot record the lead arrived on. Estimates built in HubSpot let the estimate be built from the HubSpot deal or contact record without leaving HubSpot, and Estimates built in FieldRanger keep an estimate built in FieldRanger tied to the deal it belongs to. Through PandaDoc, estimates and agreements go out for signature. Won deals become jobs with their context carried over, and each day of a multi-day job is its own job in FieldRanger, assigned to a technician, because multi-day jobs are not built.

Job-level time tracking logs clock-in and clock-out against each job, which is the record that turns into labor hours per device on the next estimate. Materials tracking logs the parts and cable used on each job for job costing, and Warehouse-specific inventory checkout records which warehouse the stock came from. Photo documentation attaches rough-in photos to the work order before the walls close. Invoices from completed work orders produce the bill, Stripe takes payment in the field, QuickBooks syncs invoices and payments, and Revenue reports show job revenue and margin by service type.

FieldRanger has no plan takeoff tool, so device counts are built in the estimating spreadsheet, and unit prices come from the price book of services, parts and rates. Progress billing and retainage are not built. The electrical estimate template carries the fields of a finished estimate, the estimate record is described on the estimating software page, and plans are on pricing, where Start free trial runs 14 days with no card.

Frequently asked questions

How to estimate residential electrical work?

Take off every device from the plans by type and room, check the counts against the adopted code, assign labor hours per device and per circuit, build the material list from the same counts, add the local permit fee, then add overhead and margin.

How is a residential electrical job priced per opening?

A past job's total is divided by its openings, and the average is applied to the next job. The average holds only for the same device mix; in the Madison sample, a lighting-heavy mix priced per opening comes in $538.45 short.

How many receptacles does a room need under the 2023 NEC?

Enough that no point along the floor line of any wall is more than 6 feet from a receptacle, counting any wall space 2 feet or wider, under section 210.52(A). Hallways 10 feet or longer need at least one.

How much is an electrical permit in Madison, Wisconsin?

For work in an existing building, $25.00 for the first ten new or altered openings and $1.00 for each one after, and $50.00 per service panel for a service replacement, rounded up to the next dollar.

Where do labor hours per device come from?

From the company's own clocked jobs: hours divided by devices installed, by device type. Published labor unit manuals give starting values until enough jobs are recorded.

The Madison basement prices at $5,834.15 from 46 counted openings, and the count, not the average, is what keeps a lighting-heavy basement from going out $538.45 short.

Run field service on HubSpot with FieldRanger

Estimates with e-signature, scheduling and dispatch, a technician mobile app and invoicing, synced to the HubSpot deals and contacts the business already keeps.

Book a demo