Guide

HVAC Replacement Quote:Manual J Sizing, Good-Better-Best Equipment Tiers, SEER2 Floors, A2L Refrigerants, Utility Rebates, Financing and an Austin Sample

HVAC replacement quote guide: Manual J sizing, good-better-best tiers, SEER2 floors, A2L refrigerants, Austin Energy rebates, financing and a costed sample.

By Published Updated

15 min read

An HVAC replacement quote is the fixed price for removing a heating and cooling system and installing a new one, written after a Manual J load calculation. It offers equipment in tiers by efficiency rating, names the refrigerant each tier uses, lists labor and permit lines, and shows any utility rebate and financing apart from the cash price.

A replacement quote fails in ways that surface after the sale. A tier priced below the regional efficiency floor cannot legally be installed. A rebate printed on the quote is refused because the program wanted a load calculation report the contractor never ran. A monthly payment in a flyer triggers federal disclosure rules the flyer does not meet. FieldRanger makes HVAC software that runs inside HubSpot, and this page belongs to its pricing and quoting guides. It follows the order of a replacement sale: the estimate stages, the load calculation, the equipment tiers and their federal floor, and the refrigerant line. It then covers one utility's rebate rules and financing, and closes with a three-tier quote costed for a house in Austin, Texas.

Four terms carry the page. An equipment tier is one complete system offered at one efficiency level, so a quote with three tiers prices three systems for the same house. Manual J is the residential load calculation published by the Air Conditioning Contractors of America (ACCA). An A2L refrigerant is one with lower flammability under the ASHRAE safety classification, the class that R-454B and R-32 belong to. A rebate path is the set of conditions a utility program attaches to a payment, and one program may offer more than one.

Estimate for HVAC replacement: range, site visit and signed quote

A homeowner asking for an estimate for HVAC replacement receives three documents in sequence, and each commits the contractor to more. The first is a range given by phone or web form, built from the house's floor area and the age of the old system. The second is the site visit, where the load is calculated and the ducts, panel and equipment location are seen. The third is the written quote: one price per tier, valid until a printed date, signed to accept.

The range commits to nothing, and the quote states what changed between them. A range given for a 3.5-ton system that becomes a 3-ton quote after the load calculation records a finding, not an error. Utility programs build the same sequence into their rules. Austin Energy's whole-home program states that its participating contractors "conduct a no-cost, in-home energy assessment" and "leave an estimate for any recommended work" (Austin Energy, Home Energy Savings, read November 13, 2026). Repair pricing, where the document follows a diagnosis rather than a load calculation, is covered in the HVAC repair estimate guide.

Manual J load calculation on the quote

The capacity on a replacement quote comes from the house, not from the data plate of the unit being removed. ACCA describes Manual J 8th Edition, published as ANSI/ACCA 2 Manual J - 2016, as "the national ANSI-recognized standard for producing HVAC equipment sizing loads" for detached houses, townhouses, condominiums and manufactured homes. ACCA adds that a load calculation performed under it "is required by national building codes and most state and local jurisdictions" (ACCA, Manual J Residential Load Calculation, read November 13, 2026).

The calculation needs inputs that only the site visit collects: window area and orientation, insulation levels, infiltration, and the share of duct run in unconditioned space. ACCA's description of the 2016 edition notes a new documentation requirement to state whether "AED exists", meaning adequate exposure diversity. A quote that records the calculated heating and cooling loads, in Btu per hour, lets the customer compare tiers on the same capacity.

The report also has a second reader. Austin Energy requires the installer to "size equipment to an approved ACCA Manual J methodology" and to attach proof of sizing to the rebate application (Austin Energy, Air Conditioning rebates, read November 13, 2026). A contractor who sizes by rule of thumb loses the rebate on every tier it would have paid.

Good, better and best equipment tiers against the federal floor

Tiers are a trade practice: three complete systems at rising efficiency and price, so the customer chooses a level rather than a yes or no. The lowest tier is bounded by federal law. The Department of Energy's guidance on the 2023 standards sets a national minimum of 14.3 SEER2 and 7.5 HSPF2 for split-system heat pumps manufactured from January 1, 2023, and 13.4 SEER2 for split-system air conditioners. Split air conditioners under 45,000 Btu per hour installed in the Southeast, which includes Texas, must reach 14.3 SEER2 (DOE, 2023 Central Air Conditioner Standards FAQ, issued October 5, 2022).

The national standard follows the manufacture date; the Southeast standard follows the installation date. DOE's guidance quotes 10 CFR 430.2: installation means "the connection of the refrigerant lines and/or electrical systems to make the central air conditioner operational". DOE's enforcement page states that "the 'Southeast' standards only apply to split-system air conditioners". It also states that DOE can request an installer's records, which "must be provided to the DOE within 30 days". Remediation means replacing the noncompliant unit "at no cost to the consumer" (DOE, Regional Standards Enforcement, last updated March 5, 2018, read November 13, 2026).

The top of the range is set by the market, and in Austin the middle is set by the rebate table. Austin Energy's heat pump tiers start at 15.2 SEER2, 11.0 EER2 and 7.8 HSPF2. A tier priced at the federal floor therefore earns no rebate there, and the quote says so on that tier's line.

Three heat pump tiers for one Austin house, against the federal floor and Austin Energy's table (ratings are sample certified combinations; floors and rebate tiers as cited above)
TierRatings (sample)Federal floorAustin Energy heat pump tier
Good: single-stage14.3 SEER2, 7.5 HSPF2Meets 14.3 SEER2 and 7.5 HSPF2 exactlyBelow Tier 1: no rebate
Better: two-stage16.0 SEER2, 11.0 EER2, 8.0 HSPF2AboveTier 2
Best: variable-speed17.0 SEER2, 13.0 EER2, 9.0 HSPF2AboveTier 3

The ratings belong to the certified combination of outdoor unit and air handler, not to either unit. Each tier line on the quote names both model numbers, so the ratings can be checked against the manufacturer's certificate before the rebate is applied for.

Refrigerant line: A2L pairs and the new-system test

A full replacement is a new system under EPA's Technology Transitions rules, and that decides the refrigerant. EPA's homeowner answers state that a new system is installed "if both the condensing unit and indoor coil are replaced together" (EPA, Frequent Questions on the Phasedown of HFCs, last updated September 14, 2026). Keeping the existing refrigerant lines does not change the answer. EPA's May 2026 fact sheet adds that "increasing the cooling capacity, in BTU per hour, of an existing system" also counts as a new installation (EPA, Technology Transitions final rule fact sheet, updated May 2026).

New residential systems carry a global warming potential (GWP) limit of 700 from January 1, 2025. The current sector table adds an exception for older stock. It lists "no installation compliance date for systems where all specified components were manufactured or imported prior to January 1, 2025" (EPA, Technology Transitions HFC restrictions by sector, last updated August 28, 2026). EPA's reference table lists GWPs of 2,088 for R-410A, 465 for R-454B and 675 for HFC-32, also called R-32 (EPA, Technology Transitions GWP reference table, last updated April 2, 2026). The HVAC quote guide covers the wording for R-410A equipment built before 2025.

The two lower-GWP refrigerants are A2L. EPA's SNAP list for residential air conditioning and heat pumps classes HFC-32 and R-454B as A2L. Each is listed as "acceptable with use conditions" (EPA, SNAP substitutes in residential and light commercial air conditioning and heat pumps, last updated March 19, 2026). EPA's answers add that SNAP and industry standards "prohibit the use of flammable or mildly flammable refrigerants such as HFC-32 or R-454B in systems that were not designed to use them". A replacement quote therefore prices a matched A2L pair, and it does not offer an A2L condenser on the old R-410A coil.

Austin Energy rebates: tiers, conditions and the two paths

A rebate belongs on the quote only in the words and amounts of the program's own page, on the day the quote is written. Austin Energy publishes two heat pump tables. The air-conditioner-only path pays $650, $750 and $950 for Tiers 1 to 3. The Home Energy Savings path pays $1,000, $1,300 and $1,600 for the same tiers, and adds rebates for building measures. Two of those measures are mandatory. Air infiltration and duct sealing pay "$0.20 per sq ft of floor area", and total external static pressure pays "$175.00 for the first system" (both pages as cited above, read November 13, 2026).

Austin Energy heat pump rebate conditions that change the quote (program pages read November 13, 2026)
ConditionAir conditioner rebate pathHome Energy Savings path
ContractorAustin Energy participating contractorParticipating contractor performs the assessment and all improvements
AgeExisting system and home both 10 years old or olderHome 10 years old or older
ScopeCondenser, air handler or furnace, and coil all replacedAll recommended and approved improvements done with the new system, minimum of three qualifying upgrades
SizingManual J or Austin Energy sizing guidance, proof attachedContractor helps choose right-sized equipment
Deadline and checksApplication within 90 days of installation; post-installation inspectionMinimum of $100 in rebates to participate

Three conditions reach back into the quote itself. The all-components rule means every rebated tier is a new system under EPA's test, so every rebated tier carries an A2L refrigerant unless its components were built before 2025. The AC page also excludes "air conditioning systems with electric resistance heating elements". The page does not say how that applies to a heat pump's backup heat strip, so the contractor confirms with the program before printing a rebate on a tier with strip heat. Finally, the Home Energy Savings page announces increased rebates "starting Dec. 1st" without naming a year. A quote dated after December 1 rereads the table rather than copying an older quote.

The rebate is paid by the utility after inspection, not deducted by the contractor: on a rebate-only project, the page states, the customer receives "a rebate check at the end of the project". The quote therefore shows the cash price, then the expected rebate on its own line, then the net cost, and names the condition that releases each rebate. The federal tax credit line is covered in the HVAC quote guide; a 2026 installation falls outside it.

Financing beside the cash price

Financing on a replacement is a trade practice with two sources: a lender the contractor works with, or a program loan. The quote keeps the cash price as the price, and shows financing as a way to pay it. Austin Energy's program names a loan through Velocity Credit Union, with "applicable rebates" applied to the project cost. Its loan table lists a minimum credit score of 600, loans from $1,500 to $25,000 and terms up to 120 months (Home Energy Savings page, read November 13, 2026).

The same page gives two dates for its zero-percent rate. The banner offers the rate "now through September 30, 2027". The loan table states "December 1 – September 30, 2026". A quote prints a monthly payment only after the credit union confirms the rate and term for that customer, and it names the lender and the date of the confirmation.

Advertising carries a federal rule that a quote handed to one customer does not. Under Regulation Z, an advertisement may state "the number of payments or period of repayment" or "the amount of any payment". If it does, it must also state the down payment, the repayment terms and the "annual percentage rate", using that term (CFPB, 12 CFR 1026.24, read November 13, 2026). A yard sign or web page reading "new heat pump from $119 a month" states a payment amount, so it carries the full set.

Sample three-tier replacement quote in Austin, Texas

The sample replaces a 2011 3.5-ton split heat pump and air handler using R-410A, at a 1,850-square-foot house built in 1996. The load calculation, equipment prices, materials, hours, permit fee, disposal, add-on work and margin are sample figures. The wages are sourced from BLS 2025 wage data for the Austin-Round Rock-San Marcos metro. HVAC mechanics and installers there earned $35.97 an hour at the 75th percentile and $23.59 at the 25th (O\*NET OnLine, Texas wages for 49-9021.00, read November 13, 2026). Payroll taxes are 6.2 percent Social Security and 1.45 percent Medicare (IRS Topic 751, updated November 9, 2026).

The sample Manual J gives a cooling load of 31,200 Btu per hour, so every tier is a 3-ton system with a matched air handler. The old 3.5-ton unit was oversized for the house as it now stands.

Lines shared by all three tiers (wages and tax rates sourced; other inputs labelled samples)
LineBasisAmount
Manual J calculation and reportSample charge$175.00
MaterialsLine set flush, pad, disconnect and whip, condensate, thermostat (sample)$780.00
Lead installer, 9 hours$35.97 × 1.2465 (7.65% payroll taxes + 17% benefits and insurance, sample) = $44.84 an hour$403.56
Helper, 9 hours$23.59 × 1.2465 = $29.40 an hour$264.60
PermitSample fee; the City of Austin fee schedule sets the real one$160.00
Refrigerant recovery and disposal of the old systemSample cost$95.00
Shared costSum of the lines$1,878.16
Sample three-tier quote at a 40% gross margin (price = cost ÷ 0.60; rebates from Austin Energy's AC table)
TierEquipment (sample)Full costQuoted priceAC-path rebateNet to the customer
Good: 14.3 SEER2, R-454B$4,150.00$6,028.16$10,046.93$0.00$10,046.93
Better: 16.0 SEER2, R-454B$5,450.00$7,328.16$12,213.60$750.00$11,463.60
Best: 17.0 SEER2, R-32$7,300.00$9,178.16$15,296.93$950.00$14,346.93

Equipment is 68.8 percent of the Good tier's cost and 79.5 percent of the Best tier's, so an error in the distributor price moves the top tier further. The gap between Good and Best is $5,250.00 in quoted price and $4,300.00 net of the rebate.

The Home Energy Savings path changes the scope as well as the rebate. On the Best tier it adds duct sealing at a sample price of $950.00 and a static pressure test and correction at $225.00, for a price of $16,471.93. Its rebates are $1,600.00 for the heat pump, $370.00 for duct sealing (1,850 square feet × $0.20) and $175.00 for static pressure, or $2,145.00. The net is $14,326.93: $20.00 less than the AC-only path, with the ducts sealed. On the Better tier the same add-ons give a net of $11,543.60, which is $80.00 more than the AC-only path.

Financed through the program loan at a confirmed zero percent over 120 months, the Best tier's $14,326.93 balance would be $119.39 a month. That figure goes on the quote with the lender's confirmation date, and in no advertisement without the Regulation Z terms.

Texas tax follows the contract form. Comptroller Publication 94-116 states that labor to repair, remodel or restore residential real property "is not taxable". Under a lump-sum contract, the contractor pays tax on supplies and materials when buying them and does not charge the customer tax (Texas Comptroller, Publication 94-116, read November 13, 2026). The sample is written as a lump-sum contract, so its equipment and material costs include the tax paid to suppliers and the quote carries no tax line.

HVAC replacement quote checklist

  1. Give the phone or web range as a range, with the floor area and old system it assumed.
  2. Run Manual J at the site visit and print the heating and cooling loads on the quote.
  3. Price each tier as a certified combination, with both model numbers and the ratings.
  4. Check the lowest tier against the federal floor for its type, and for an air conditioner against the Southeast or Southwest floor by installation date.
  5. Name the refrigerant on every tier, and treat a condenser and coil replaced together, or an increase in capacity, as a new system.
  6. Read the rebate program's page on the day of the quote, and copy its amounts, tiers and conditions with the date read.
  7. Show the cash price, the expected rebate, the condition that releases it and the net cost as separate lines.
  8. Print a monthly payment only after the lender confirms the rate and term, and keep payment amounts out of advertising unless the Regulation Z terms appear with them.
  9. Set the tax treatment from the state's rule for the contract form chosen.
  10. State the expiry date and who pulls the permit and books the inspection.
  11. Verify after installation: compare the clocked hours and materials with the quote, file the rebate within the program's deadline, and record the inspection result on the job.

Replacement quotes, signatures and install days in FieldRanger

FieldRanger keeps the replacement quote on the HubSpot record the sale runs on. Estimates built in HubSpot are built from the deal or contact record without leaving HubSpot, and Estimates built in FieldRanger stay tied to the HubSpot deal they belong to. The estimate goes out for signature through PandaDoc, and a won deal becomes a job with its context carried over. The estimating software page describes the estimate record.

On install day, Digital work orders put the scope and the model numbers on the assigned technician's phone. Photo documentation attaches the old data plate, the new equipment and the finished install to the work order. Job files such as the Manual J report can be kept in Google Drive. Job-level time tracking logs hours against the job, which supplies the comparison in step 11. Invoices from completed work orders produce the bill, Stripe takes payment in the field, QuickBooks syncs invoices and payments, and Revenue reports show margin by service type, so replacements read separately from repairs.

The lender, the utility and the system designer keep their own steps: the financing application, the rebate application and the Manual J calculation run in their tools, and the report is kept with the job. A deposit invoice can go out when the quote is signed, with the balance invoiced on completion; progress billing is not built. Multi-day jobs are not built: an install that runs two days is two jobs, each carrying both the lead installer and the helper. After the install, Recurring job templates schedule maintenance visits, which the HVAC maintenance checklist covers. The HVAC quote guide builds the quote line by line, and plans are on pricing, where Start free trial runs 14 days with no card.

Frequently asked questions

What should an HVAC replacement quote include?

The Manual J loads, each equipment tier as a certified combination with model numbers and ratings, the refrigerant, labor, materials, permit and disposal lines, the cash price, any rebate with its conditions, financing terms if confirmed, and an expiry date.

How is an estimate for HVAC replacement different from the quote?

The estimate is a range given before the site visit, built from floor area and the old system. The quote follows a load calculation at the house, prices each tier at one figure and becomes the price when signed.

Is a Manual J load calculation required for an HVAC replacement?

ACCA states that national building codes and many state and local jurisdictions require a Manual J calculation. Utility programs can require it too: Austin Energy asks for proof of Manual J sizing with each rebate application.

What SEER2 rating does a replacement heat pump need?

DOE guidance sets a national minimum of 14.3 SEER2 and 7.5 HSPF2 for split heat pumps made from 2023. Split air conditioners under 45,000 Btu per hour installed in the Southeast or Southwest need 14.3 SEER2.

Does a replacement system have to use A2L refrigerant?

A condensing unit and indoor coil replaced together form a new system under EPA rules, with a GWP limit of 700. R-454B and R-32 meet it and are classed A2L; a system whose components were all made before 2025 has no installation deadline.

Can a utility rebate be deducted from the replacement quote?

Austin Energy pays its rebate to the customer after the installation and inspection, so the quote shows the cash price, the expected rebate and its conditions, and the net cost on separate lines.

The Austin sample's Best tier nets $14,346.93 on one rebate path and $14,326.93 on the other; the $20.00 between them buys sealed ducts, and only a quote that prints both paths lets the homeowner see that trade.

Run field service on HubSpot with FieldRanger

Estimates with e-signature, scheduling and dispatch, a technician mobile app and invoicing, synced to the HubSpot deals and contacts the business already keeps.

Book a demo