Industry

Utility Locating Software:FieldRanger for Locating, Meter and Line Clearance Contractors on HubSpot

Utility locating software on HubSpot: FieldRanger dispatches locates, meter exchanges and line clearance work, with photos of each mark on the work order.

Updated 8 min read

Utility locating software assigns locate requests to technicians, records the marks each technician leaves at the dig site, and keeps the proof that each request was answered in time. FieldRanger handles the dispatch and the record inside HubSpot. The 811 ticket feed itself comes from a ticket management system, which FieldRanger is not.

Utility contractors appear in field service software by industry as three trades with three rulebooks. Contract and private locators mark buried lines before excavation, under state dig laws. Meter contractors install and exchange meters for utilities, in programs of thousands of addresses. Line clearance contractors trim trees around overhead conductors, under OSHA's electric power standard. FieldRanger serves each of them within the limits set out below.

811 notice and Ohio's marking deadlines

Dialing 811 reaches the state's one-call center from anywhere in the country. The center records the dig location and notifies companies that may operate facilities there, and those companies "must visit the excavation site and mark the exact location of their facilities with flags or paint". PHMSA states that every state requires by law a call "48 to 72 hours before digging", and that one-call centers "process tens of millions of incoming locate tickets annually" (PHMSA, call before digging, checked November 12, 2026).

Each state sets its own clocks. Ohio's, in sections 3781.28 and 3781.29 of the Revised Code as amended effective June 9, 2026, run as follows (ORC 3781.28; ORC 3781.29, checked November 12, 2026):

Ohio dig law clocks for excavators and utilities, ORC 3781.28 and 3781.29 (effective June 9, 2026)
PartyDutyDeadline or rule
ExcavatorNotify the protection service of the site and start dateAt least two working days, not counting the day of notice, and not more than sixteen calendar days before digging
UtilityLocate and mark its facilities to show their courseWithin two working days, not counting the day of notice
UtilityMark in the statutory colorsElectric safety red, gas and oil high visibility safety yellow, water safety precaution blue, among others, under the Ohio universal marking standards
Utility that neither marks nor contacts the excavator in timeSilenceDeemed notice that it has no facilities at the site
Utility that cannot mark accuratelyMark to the best of its abilityNotify the excavator that the markings may not be accurate

The utility also reports to the protection service for its positive response system, the channel through which the excavator learns that each facility owner has marked or cleared the site. A contract locator works inside the utility's two-working-day clock, so the locate's due time is the figure the dispatcher schedules against.

Locate requests as FieldRanger jobs

In FieldRanger, a locate is a job with an address, a due time and a technician. The ticket number goes on the work order with the excavator's description of the dig. Time window management sets the arrival window from the due time and tracks on-time performance, so the share of locates marked within the statutory window is a report, not a reconstruction. FieldRanger builds each locator's route for the day automatically, with live traffic in the ETAs, and dynamic rerouting adjusts the route when an emergency ticket is added mid-day.

At the site, the clock-in records where the locator stood. A checklist per facility type records each line marked or cleared, and before and after photos of the paint and flags attach to the work order. When the excavator later disputes a mark, the record holds the location, the time and the photos of what was on the ground. The completion and notes are logged to the HubSpot timeline of the utility or excavator the locator works for.

FieldRanger is not ticket management software: one-call tickets do not arrive in FieldRanger on their own, and positive responses are not sent from it. A locating company that receives tickets by the thousand works from a ticket management system for both functions. A private locating firm, hired by a property owner or contractor to mark lines that no member utility claims, works from quotes and invoices instead. Its requests arrive by phone, a HubSpot form or online booking, calls through HubSpot calling or Aircall are logged on the customer's HubSpot record, and FieldRanger fits that business directly.

Meter exchanges and AMI programs

Meter work is high in volume and dense in route. The U.S. Energy Information Administration counted about 119 million advanced metering infrastructure (AMI) installations in 2022, about 72 percent of electric meter installations (EIA, how many smart meters are installed, last updated October 20, 2023). Each conversion, failed unit or replacement on either side of that figure is a field visit to one address.

FieldRanger fits an exchange program address by address. Bulk scheduling assigns a feeder's worth of addresses in one pass, multi-stop planning makes a day of exchanges one route, and territory management holds each installer to a service zone. Meters are checked out of the specific warehouse that holds them or out of the installer's truck, each its own stock location, so the count of meters on hand stays true at each yard. On each work order, the installer photographs the old meter's final read and the new meter's serial, and the checklist records the seal and any socket damage. A refused access or a locked gate is a note on the job and a new job on the calendar for the second attempt.

Line clearance tree trimming under OSHA 1910.269

OSHA's electric power standard defines line-clearance tree trimming by distance: work within 3.05 meters (10 feet) of electric supply lines and equipment at 50 kilovolts or less to ground, with 0.10 meters (4 inches) added for every 10 kilovolts above that. Paragraph (r) then sets the rules on site (29 CFR 1910.269, Cornell LII, checked November 12, 2026):

  • (r)(1)(i): "Before an employee climbs, enters, or works around any tree, a determination shall be made of the nominal voltage" of the lines posing a hazard.
  • (r)(1)(ii): "There shall be a second line-clearance tree trimmer within normal (that is, unassisted) voice communication" when a trimmer will approach closer than 10 feet to a conductor energized above 750 volts, when branches being removed are closer to such lines than the distances in Tables R-5 through R-8, or when roping is needed to remove branches from the conductors.
  • (r)(1)(iii): line-clearance tree trimmers keep the minimum approach distances in Tables R-5 to R-8.

Skill-based assignment matches each span to technicians qualified as line-clearance tree trimmers, and the work order's checklist opens with the nominal voltage determination before any other step. One job can carry several technicians, so a two-person span is one job with both qualified trimmers assigned, and the second trimmer that (r)(1)(ii) requires sits on the same work order.

Ticket management systems compared with FieldRanger

Utility locating solutions come in two kinds: ticket management systems connected to one-call centers, and field service software that runs crews, jobs and invoices. Irth describes its 811 ticket management system as "Connected to Every One Call Center in North America", with "Automated positive response to one call and excavators" and "Automated ticket screening, routing, and dynamic dispatching" (Irth, 811 ticket management, checked November 12, 2026). A contract locator whose work is the one-call ticket stream is better served by a system of that kind, because ticket intake and positive response are the core of its day and FieldRanger has neither.

FieldRanger fits the utility contractor whose customers are accounts: a private locating firm, a meter exchange contractor on a utility program, or a line clearance contractor bidding circuits. The bid is a HubSpot deal; the estimate is built on it or in FieldRanger; the won deal becomes jobs with its context carried over; and invoices generated from completed work orders sync to QuickBooks. That model is described under HubSpot field service, and the board that assigns the work follows the rules of any dispatch software. Contractors whose work starts on the customer's side of the meter, such as heating and cooling or building maintenance, are covered under HVAC software and facility management software.

Utility locating guides and definitions

  • What is utility locating: the definition, a Florida locate ticket as an example, and how 811 locating, private locating and subsurface utility engineering differ.

Frequently asked questions

What is utility locating software?

Software that assigns locate requests to technicians, records the marks left at each dig site and keeps proof that each request was answered on time. FieldRanger handles the dispatch and the record inside HubSpot; it does not receive 811 tickets from one-call centers.

What is utility locating ticket management software?

Software connected to state one-call centers that receives locate tickets, screens and routes them, and sends positive responses back to the center and the excavator. FieldRanger is not ticket management software and does not receive one-call tickets.

How long does a utility have to mark lines in Ohio?

Under ORC 3781.29, as amended effective June 9, 2026, a utility locates and marks its facilities within two working days, not counting the day of notification. A utility that neither marks nor contacts the excavator in that time is deemed to have given notice that it has no facilities at the site.

What do the colors of utility marks mean?

Ohio's statute assigns safety red to electric power lines, high visibility safety yellow to gas and oil, and safety precaution blue to water systems, among other colors, under the Ohio universal marking standards.

What does OSHA require for line clearance tree trimming?

Under 29 CFR 1910.269(r), the nominal voltage of hazardous lines is determined before work starts, a second line-clearance tree trimmer is within voice communication in the conditions listed in (r)(1)(ii), and minimum approach distances from Tables R-5 to R-8 are kept.

What is utility contractor software?

Software that runs the bids, crews, jobs and invoices of a contractor working for utilities: locating, meter exchanges, line clearance and similar programs. FieldRanger does this on HubSpot records, without 811 ticket intake.

Under Ohio's law, a utility's silence for two working days tells the excavator the ground is clear, so the locator's record of arrival, marks and photos is the only evidence that the silence was not the answer. In FieldRanger that record sits on the job and on the customer's HubSpot timeline. The other trades are under field service software by industry, crew boards under dispatch software, and plans per technician on pricing, where Start free trial takes no card for 14 days.

FieldRanger runs field service inside HubSpot

Estimates, scheduling and dispatch, a technician app and invoicing on the HubSpot records sales already keeps. Every plan starts with a free trial.

Book a demo