Guide
Commercial Soft Washing:Storefronts, HOA Buildings and Dumpster Pads, SDS Chemical Handling, Portland Discharge Conditions and Bid Costing
Commercial soft washing for storefronts, HOA buildings and dumpster pads: SDS chemical handling, Portland's wash water requirements and pricing inputs.
Commercial soft washing is low-pressure cleaning of commercial building exteriors and paved areas with a diluted sodium hypochlorite mix and a surfactant, applied, left to dwell, then rinsed. It covers storefront facades and canopies, HOA building exteriors and dumpster pads, and it differs from house washing in access, chemical volume, wash water handling and contract terms.
The commercial version of the job goes wrong in places a house wash does not reach. Mix runs down an aluminum storefront frame and sits there. Rinse water crosses a parking lot into the storm drain in front of the anchor tenant. A dumpster pad is degreased with an acid product and then treated with bleach. A price per square foot leaves out the lift, the after-hours premium and the recovery rig. This guide sits under the power washing software page of FieldRanger. It compares commercial and residential work, takes storefronts, HOA buildings and dumpster pads in turn, sets out chemical handling from a manufacturer's safety data sheet and the City of Portland's wash water rules, then lists the inputs that set a price and costs a sample job.
Four terms carry the page. Soft washing cleans by chemistry at low pressure, while pressure washing cleans by water force. Dwell time is the period the mix stays on the surface before rinsing. Mix strength is the share of sodium hypochlorite in the applied solution, diluted from a concentrate such as 12.5 percent. A safety data sheet (SDS) is the manufacturer's standard document on a chemical's hazards, handling, protective equipment and transport.
Commercial soft washing compared with residential soft washing
The chemistry is the same on a strip center and a two-story house. The job around it is not, and five differences decide the price and the risk.
| Dimension | Commercial soft washing | Residential soft washing |
|---|---|---|
| Customer | Property manager, owner's agent or HOA board | Homeowner |
| Surfaces | EIFS, painted block, brick, metal canopies, glass, concrete flatwork | Vinyl, fiber cement, wood, roofs |
| Access | Lifts above two stories, tenant hours, after-hours work | Ladders and extension wands |
| Wash water | Paved sites draining to storm inlets; recovery and permitted discharge | Lawns and beds beside the house |
| Contract | Scope by building and elevation, insurance certificate, recurring schedule | One-off visit, priced per house |
The homeowner version, from mix strength to the conversation at the door, is covered in residential soft washing. Setting up the company itself, with its runoff rules and the roof and siding makers' guidance, is in the soft washing company guide.
Storefront facades, canopies and EIFS
Strip centers and street-front retail combine three surface types in one elevation: an EIFS or stucco band, a metal canopy or awning frame, and aluminum storefront framing around glass. Each one sets its own limit.
EIFS. Dryvit, an EIFS maker, tells cleaners to "use a low-pressure washer (under 500 psi) with a fan spray tip, keeping the nozzle at least 12 in. (30.48 cm) from the surface", and calls pre-wetting the wall "the number one oversight in proper cleaning procedures" (Dryvit, Essential EIFS Maintenance and Repair Guide, checked November 13, 2026). The same page notes that Dryvit facades "can generally be cleaned from the ground", which removes the lift from many single-story jobs.
Aluminum and galvanized metal. The sodium hypochlorite SDS cited below lists the solution as "corrosive to metal: aluminum, zinc". Storefront frames, canopy fascias and galvanized rails are therefore pre-wet, kept out of the spray where the scope allows, and rinsed before the mix dries on them.
Glass and signage. Mix that dries on glass leaves a residue that the tenant sees first. The rinse sequence runs top to bottom with the glass last, and illuminated signs are switched off and covered before any water reaches them.
HOA buildings and common areas
An HOA job is a set of buildings priced and scheduled as one contract. The customer is the association, acting through its board or a management company, and the people affected are residents who did not sign it.
The scope therefore names more than square footage. It lists the buildings and the order in which they are washed, the notice residents receive (windows closed, vehicles moved, patio furniture covered), the water source and who pays for it, and the date the work moves if weather stops it. The certificate of insurance lists the association, or the party the board names, as certificate holder. Common-area walks, mail kiosks and pool decks are priced as separate lines, because each has its own drainage and its own users at the time of the wash.
A recurring cycle, such as one building group each spring, turns one sale into a schedule. The contract states the cycle, the price for each visit and the notice period for changes.
Dumpster pads, grease and trash enclosures
Dumpster pads collect food waste, grease and leachate, and the wash water carries all three. Portland names "trash receptacle cleaning services" among the businesses that need its Mobile Washer Discharge Authorization to discharge to the sanitary sewer, and requires that "wastewater containing fats, oils, and grease (FOG), polar and non-polar, must be treated through an approved grease removal device prior to discharge to the sanitary sewer" (City of Portland, Guide to the Mobile Washer Program, checked November 13, 2026).
Chemistry on the pad needs one rule above the others: degreaser and hypochlorite are never mixed or applied back to back without a rinse. The sodium hypochlorite SDS lists a "risk of violent reaction" with acids, names hypochlorous acid and chlorine among its hazardous decomposition products, and lists ammonia as forming chloramines. A degreaser's own SDS states whether it is acidic, alkaline or ammonia-based, and the crew reads it before the pad is wet.
Chemical handling from the INEOS sodium hypochlorite SDS
The INEOS KOH safety data sheet for Sodium Hypochlorite 12.5-15.6 Solution, revised May 20, 2026, is the reference here (INEOS KOH SDS). A crew uses the SDS of the product it actually buys; the sections below are the ones that set field practice.
- Hazards (Section 2). H314, "Causes severe skin burns and eye damage", and serious eye damage Category 1.
- Protective equipment (Section 8). "Wear chemical splash goggles and face shield", chemical-resistant impervious gloves and a rubber apron; respiratory protection is selected on the exposure and used under a respiratory protection program.
- Storage (Section 7). In the original container, protected from direct sunlight, in a dry, cool and well-ventilated area, separated from acids.
- Reactivity (Section 10). Violent reaction with acids; chloramines with ammonia and amines; corrosive to aluminum and zinc.
- Properties (Section 9). pH 11.5 to 13 for the concentrate.
- Transport (Section 14). UN1791, hazard class 8, packing group III. The reportable quantity is 62.252 gallons, and packages below it are not subject to the RQ transport requirements.
OSHA's hazard communication standard requires the employer to keep the SDS for each hazardous chemical "readily accessible during each work shift to employees when they are in their work area(s)", and allows electronic access where it creates no barrier to immediate access (29 CFR 1910.1200(g)(8)). For a mobile crew the work area is the truck and the site, so the SDS travels with the chemical, on paper or on the technician's phone.
Portland wash water requirements for commercial mobile washers
Portland, Oregon states its rules on one set of pages from its Bureau of Environmental Services, and they show what a city can require of a commercial wash.
The prohibition comes from three code chapters. "Portland City Code 17.39 prohibits the discharge of wash water from pressure washing and graffiti removal into the stormwater system"; Code 17.32 prohibits directing water onto any city sidewalk, street, easement or right-of-way without authorization; and Code 17.34 requires approval to discharge to the sanitary sewer (City of Portland, Pressure Washing and Graffiti Removal, checked November 13, 2026). Routine rinsing of pavement and building exteriors may reach the stormwater system only where "chemicals, soaps, detergents, steam, or heated water are not used" (City of Portland, Cleaning Your Building or Sidewalk). A soft wash uses chemicals by definition, so its water is contained.
A business that discharges to the sanitary or combined sewer applies for a Mobile Washer Discharge Authorization and meets its conditions:
- All washing is performed on the customer's property, and wash water is contained on site; washing in the right-of-way is prohibited.
- The wash area is washed down after use, with no soap residue left on the site.
- Water is collected and discharged to the sanitary or combined sewer at an approved location, with FOG treated first.
- The discharge pH is between 5.0 and 11.5, verified on site with pH test strips or a portable tester before discharge.
- The discharge rate does not exceed 50 gallons per minute.
- A site-specific work plan, a copy of the site drainage map and the authorization are kept in each service vehicle.
- An annual certification of compliance is submitted to keep the authorization.
Two of these conditions meet the SDS directly. The concentrate's pH of 11.5 to 13 sits at or above the 11.5 ceiling, so recovered water is tested rather than assumed to be within the limit. The work plan and drainage map are per customer site, so a recurring commercial account carries them in its job record for every visit.
Aerial lifts and after-hours access
Above the reach of ground equipment, commercial facades bring an aerial lift onto the job. OSHA's aerial lift fact sheet sets out a pre-start inspection before each work shift, operation only by trained and authorized workers, a distance of at least 10 feet from overhead power lines treated as energized, and "a body harness or a restraining belt with a lanyard attached to the boom or bucket" (OSHA, Aerial Lifts fact sheet).
Access also has a clock. Retail tenants open at fixed hours, and a property manager may restrict wet work to before opening or after close. The time window is part of the scope, priced as its own line when it moves labor outside the normal day.
Bid inputs for a commercial soft wash
A commercial price is built from measured inputs rather than a single rate, because two storefront rows of the same area can need different lifts, mixes and recovery work. The inputs, in the order they are collected:
- Area by elevation and surface. Square feet of EIFS, masonry, metal and glass, measured per elevation, with heights.
- Mix strength and volume. The applied strength the cladding maker allows, and the gallons of mix the area takes, converted to gallons of concentrate.
- Access. Ground, ladder or lift, with the rental quoted for the dates.
- Wash water. Containment, recovery, pH testing and the approved discharge point.
- Hours and timing. Technician hours on site and traveling, and any premium for work outside the normal day.
- Frequency. One visit or a recurring cycle, with the price per visit.
Concentrate is the easiest input to price. Alliance Chemical lists 12.5 percent sodium hypochlorite at $90.00 for a 5-gallon pail, $285.00 for four pails and $790.00 for a 55-gallon drum, or $18.00, $14.25 and $14.36 a gallon (Alliance Chemical, Sodium Hypochlorite 12.5%, checked November 13, 2026). Labor is the larger input: in the Portland-Vancouver-Hillsboro metro, cleaners of vehicles and equipment, the nearest published occupation, earned a median of $18.86 an hour and $21.78 at the 75th percentile in BLS 2025 wage data (O\*NET OnLine, Oregon wages for 53-7061.00). The employer adds 6.2 percent for Social Security and 1.45 percent for Medicare (IRS Topic 751, updated November 9, 2026).
Sample costing: a storefront row and dumpster enclosure in Portland, Oregon
The sample is a hypothetical two-technician crew washing eight storefronts and one dumpster enclosure for a property manager. Areas, mix strength and hours are sample inputs, labelled as such; the rates are the sourced figures above.
| Line | Basis | Amount |
|---|---|---|
| Facade area | 4,800 sq ft of EIFS band and canopies, single story, washed from the ground (sample) | — |
| Mix applied | 160 gallons at 1.0 percent, within the cladding maker's limits (sample) | 12.8 gallons of 12.5 percent concentrate |
| Concentrate | 12.8 gallons × $14.25 (four-pail price) | $182.40 |
| Dumpster enclosure | Degreased, rinsed between products, water recovered and pH-tested (sample) | Included in hours |
| Technician hours | 2 technicians × (7 hours on site + 1 hour travel) (sample) | 16 hours |
| Wages | 16 × $18.86 | $301.76 |
| Employer Social Security and Medicare | 7.65% × $301.76 | $23.08 |
| Direct cost before access, recovery equipment and overhead | Sum of priced lines | $507.24 |
Labor is 64 percent of the priced lines and concentrate 36 percent. At the 75th-percentile wage, the same 16 hours cost $348.48 in wages, so a crew paid to keep experienced technicians moves the floor more than any chemical price does. The table leaves out the lift (none was needed on a single story), the recovery rig, insurance, workers' compensation, the truck and overhead; each is added per job in the costing set out in the pressure washing business plan template. The direct cost per square foot of facade, $0.11, is a check on the bid, not a way to build it, because the dumpster enclosure sits inside the same hours.
Site checklist for commercial soft washing
- Each elevation is measured and its surface recorded: EIFS, masonry, metal, glass.
- The cladding maker's cleaning limits are on file, including pressure and distance for EIFS.
- Aluminum frames and galvanized metal are pre-wet and rinsed before the mix dries.
- Degreaser and hypochlorite are never combined, and the degreaser's SDS has been read.
- The SDS for each chemical is in the truck or on the technician's phone for the whole shift.
- Protective equipment matches Section 8 of the SDS: goggles and face shield, impervious gloves, apron.
- Storm inlets are protected and wash water is contained on the customer's property.
- Recovered water is pH-tested before discharge, and discharged only at an approved location.
- Lifts are inspected before each shift and kept 10 feet from overhead lines.
- The scope states the access window, resident or tenant notice and the visit cycle.
- Verify after each job: photograph the protected inlets and the pH reading, and file both with the job record.
Recurring commercial accounts in FieldRanger
FieldRanger keeps the commercial account on the HubSpot records the sale was made on. An estimate can be built from the HubSpot deal or contact record, or in FieldRanger and kept tied to its deal, and a won HubSpot deal becomes a job with its context carried over. Recurring job templates generate the visits of a maintenance contract, such as one building group each spring. Each visit's digital work order carries the job details, customer information and instructions to the technician's phone, so the site work plan travels with the job; custom checklists hold steps such as inlet protection and the pH test, and photo documentation attaches before and after photos to the work order.
Technicians clock in and out with time logged against each job, the invoice is generated from the completed work order, and revenue reports show job revenue and margin by customer or service type. Recurring work can be charged automatically to a card on file, and there is no weather feed, so a rain day is rescheduled on the drag-and-drop calendar. The recurring jobs page shows how maintenance contracts become scheduled visits, and plans are on pricing, where Start free trial runs 14 days with no card.
Frequently asked questions
What is commercial soft washing?
Low-pressure cleaning of commercial building exteriors and paved areas with a diluted sodium hypochlorite mix and a surfactant, left to dwell and rinsed. It covers storefronts, canopies, HOA buildings and dumpster pads.
How is commercial soft washing different from residential soft washing?
The chemistry is the same; access, surfaces, wash water and contracts differ. Commercial jobs add lifts and tenant hours, EIFS and aluminum framing, paved sites that drain to storm inlets, and recurring contracts with property managers or HOA boards.
Can soft wash water go into a storm drain?
Not in Portland, Oregon, where City Code 17.39 prohibits wash water from pressure washing in the stormwater system and only plain-water rinsing without chemicals may reach it. Water containing chemicals is contained and discharged to the sanitary sewer under a Mobile Washer Discharge Authorization.
What pressure is safe for cleaning EIFS?
Dryvit tells cleaners to use a low-pressure washer under 500 psi with a fan tip, at least 12 inches from the surface, and to pre-wet the wall first.
How is a commercial soft washing job priced?
From measured inputs: area by elevation and surface, mix strength and volume, access equipment, wash water recovery and discharge, technician hours and timing, and visit frequency. In the Portland sample, labor was 64 percent of the priced direct cost.
What protective equipment does sodium hypochlorite require?
The INEOS SDS calls for chemical splash goggles and a face shield, chemical-resistant impervious gloves and a rubber apron, with respiratory protection selected on the exposure under a respiratory protection program.
On the Portland sample, the chemical is $182.40 of a $507.24 floor, and the line that carries a code citation, the pH reading taken before the recovered water goes down an approved drain, costs a test strip.
Run field service on HubSpot with FieldRanger
Estimates with e-signature, scheduling and dispatch, a technician mobile app and invoicing, synced to the HubSpot deals and contacts the business already keeps.
Book a demo