Guide
Residential Soft Washing:Siding and Roof Mix Strengths, the Pool Chlorine SDS, Algae Streak Instructions, Landscaping Protection and Pricing Inputs
Residential soft washing: siding and roof mix strengths, the pool chlorine SDS, shingle makers' algae instructions, plant protection and pricing inputs.
Residential soft washing cleans a home's siding and roof with diluted sodium hypochlorite applied at low pressure, left to dwell and then rinsed, so that chemistry rather than water force removes algae, mildew and dirt. A house job adds three duties to the spraying: matching the mix to each surface maker's instructions, protecting the plantings, and keeping wash water out of storm drains.
A house wash goes wrong in the mixing, not the spraying. A crew mixes the roof batch at the siding strength and leaves the streaks, or mixes the siding batch at the roof strength and exceeds what the siding maker allows. A surfactant poured into pool chlorine meets a safety data sheet that warns against mixing it with detergents. Rinse water carries the mix into the hedge, then down the driveway to a storm inlet. FieldRanger makes power washing software for washing companies whose customers sit in HubSpot, and this guide covers the residential job itself. It starts with the surfaces a house wash covers, then sets out mix arithmetic, the chlorine safety data sheet, the shingle makers' algae instructions, plant protection and the runoff rule in one Florida county. Pricing inputs, a costed single-story house, a checklist and the job record close it.
Four terms carry the guide. Sodium hypochlorite, abbreviated SH, is the active ingredient of chlorine bleach, sold for pool and soft wash use as a 12.5 percent solution. A surfactant is the soap-like additive that helps the mix cling to a vertical surface. Dwell time is how long the mix stays on the surface before the rinse. Downstream injection draws the chemical into the water line after the pump, so the chlorine never passes through it.
House and roof surfaces in a residential soft wash
A residential soft wash covers the surfaces that low pressure and chemistry clean better than force. Vinyl siding, painted wood, stucco and fiber cement are washed with a siding mix. Asphalt shingle roofs are treated for the dark streaks of algae with a roof mix, or with a non-chlorine method where the shingle maker says so. Gutter faces, soffits, screened enclosures and fences are washed at the siding strength or below. Concrete driveways and walks are the exception: they are cleaned with a surface cleaner at pressure, and their runoff is the same problem as the soft wash runoff.
The surface material decides the method before any price is written. Fiber cement is a no-bleach surface by its maker's instructions, as the guide for a soft washing company sets out with the James Hardie, Owens Corning, CertainTeed and Ply Gem pages. The estimate therefore records the siding material and the shingle maker on every house.
Mix strength from 12.5 percent concentrate
The arithmetic is one ratio. The volume of concentrate equals the batch volume multiplied by the target strength and divided by the concentrate strength. A 1.25 percent siding mix from 12.5 percent concentrate is one part concentrate in ten parts of batch: 1 gallon of concentrate in a 10-gallon batch, or 5 gallons in a 50-gallon tank.
The 1.25 percent figure comes from a siding maker. CertainTeed's vinyl siding instructions mix one quart of 5% sodium hypochlorite with three quarts of water, plus 1/3 cup of detergent and 2/3 cup of trisodium phosphate, and warn that "Greater concentrations may cause damage to vinyl siding"; the same page does not recommend power washing vinyl or polymer siding (CertainTeed, how to clean vinyl siding, checked November 13, 2026). One quart of 5 percent solution in a gallon of mix is 1.25 percent.
| Target strength | Concentrate per 10 gallons | Water per 10 gallons | Use in the sample below |
|---|---|---|---|
| 1.25% | 1.0 gal | 9.0 gal | Vinyl siding, at CertainTeed's ceiling |
| 2.0% | 1.6 gal | 8.4 gal | Not used |
| 3.0% | 2.4 gal | 7.6 gal | Roof, a sample strength |
Concentrate loses strength in storage. The safety data sheet below tells the user to keep it out of direct sun and heated indoor areas "To maintain hypochlorite strength", so a pail stored on a hot trailer for a month mixes weaker than its label. A crew that tests the concentrate's strength before mixing works from the actual figure rather than the printed 12.5 percent.
Hasachlor safety data sheet: detergents, gloves, storage and spills
Hasa publishes the safety data sheet for Hasachlor, a 12.5% sodium hypochlorite solution whose recommended use is "Sanitizer of swimming pool and spa water" (Hasa, Hasachlor SDS No. 102, revision date August 24, 2026). It is a different maker's sheet from the ones used in the commercial and company guides, and its handling section carries a line that a house wash recipe runs into.
| SDS section | What the sheet states |
|---|---|
| 2, hazards | Skin corrosion Category 1, serious eye damage Category 1, acute aquatic hazard Category 1, corrosive to metals; signal word DANGER; "Very toxic to aquatic life" |
| 3, composition | Sodium hypochlorite 12.5%, sodium hydroxide 0.2% |
| 4, first aid | Eyes: rinse slowly and gently with water for 15 to 20 minutes |
| 6, environmental | "Do not discharge into drains, water courses or onto the ground" |
| 7, handling | Mixing with "ammonia, acids, detergents, etc or with organic materials" will release chlorine gas |
| 7, storage | Store in a cool, shaded outdoor area; do not freeze; keep in the original vented container |
| 8, protection | Safety glasses, goggles or face shield; butyl rubber, neoprene or nitrile gloves; a rubber apron where splashing may occur; an eye wash nearby |
The handling line conflicts with the siding recipe. CertainTeed's mix adds detergent to bleach; the Hasa sheet lists detergents among the materials that release chlorine gas when mixed with its product. A residential crew resolves the conflict on paper before the job: it follows the sheet for the chlorine it actually bought, and adds only a surfactant whose own label or safety data sheet states it is for use with sodium hypochlorite. The SDS for each product on the trailer, not a generic one, belongs on the job record.
Algae streak guidance from ARMA, Atlas and CertainTeed
Roof streaks are an algae problem, and the roofing industry says so in one bulletin. The Asphalt Roofing Manufacturers Association names Gloeocapsa magma as "probably the most prevalent" of the species, and places the discoloration as most widespread in the Gulf States and along the Northwest and Eastern Seaboards (ARMA technical bulletin, Algae Discoloration of Roofs, revised June 2024, hosted by Atlas Roofing). Three documents then give three different methods.
| Source | Chemical | Brushing | Pressure washer | Other statements |
|---|---|---|---|---|
| ARMA bulletin, revised June 2024 | Liquid household bleach and water; mixing directions "may vary among shingle manufacturers"; other chemicals only with the shingle maker's approval | "DO NOT use" any type of brush or broom | Not to be used | Leave on at least 15 and no more than 20 minutes; rinse gently; apply carefully to avoid damage to the surrounding landscape |
| Atlas Roofing | Oxygen bleach powder mixed with water, from a garden hose sprayer | Light scrub after about 20 minutes | "Never use a power washer on shingles" | Chlorine bleach can kill grass, shrubs and flowers, and overspill "can also void a home's termite warranty" ([Atlas, roof algae debate](https://www.atlasroofing.com/asphalt-life/roof-algae-debate-clean-it-off-or-protect-against)) |
| CertainTeed roofing | A professional applies a cleaning agent, not named | Gentle brushing with a soft-bristled broom or wide hand brush | "Do not use a power washer on your asphalt shingle roof" | No chemical strength given ([CertainTeed, roof maintenance](https://www.certainteed.com/inspiration/how-tos/what-type-maintenance-does-my-roof-require)) |
Three findings follow. The three sources agree on one point only: no pressure washer on shingles. They disagree on brushing, with ARMA forbidding any brush and both makers allowing a soft one. They disagree on chemistry, with ARMA describing chlorine bleach and Atlas recommending oxygen bleach and warning against chlorine. None of the three publishes a chlorine strength for a roof mix. A residential roof wash therefore records the shingle maker, the method the maker publishes and the strength actually mixed, and the crew photographs the roof before and after.
Plant and lawn protection around the house
The plants are the part of a house wash the homeowner sees first afterward. Atlas states that chlorine bleach can kill grass, shrubs and flowers, ARMA asks for careful application to avoid damage to the landscape, and CertainTeed suggests testing a cleaning solution on a plant and waiting a few days where plantings sit close to the house. The Hasa sheet adds that its product is very toxic to aquatic life and should not be discharged onto the ground.
The protection is a procedure written into the job, in the order the crew performs it:
- Walk the house with the homeowner and mark plantings within reach of the spray, including any the owner names as valuable.
- Wet the plants and lawn edge with plain water before the first chemical application.
- Cover low plants beside the wall where the spray or drip will land.
- Apply the mix from the bottom of the wall upward in sections, at the lowest strength that the surface maker allows.
- Rinse the plants again after each section's rinse, and once more before leaving.
- Photograph the plantings before and after, and record the covers and rinses on the work order.
Pre-wetting and rinsing dilute what reaches the leaves and soil; they do not make a chlorine mix safe for plants, so step 4 keeps the strength at the lowest the maker permits.
Runoff rules in Pinellas County, Florida
The storm drain rule is local, and the sample job sits in Pinellas County, on Florida's Gulf coast. The county prohibits "any discharge to the drainage system or to a waterway that is not composed entirely of stormwater", states that violators of the stormwater ordinance may be fined up to $10,000 per day plus cleanup costs, and directs that building exteriors cleaned with high-pressure water be protected with sandbags or berms, or the storm drain sealed with plugs or rubber mats (Pinellas County, Prevent Construction Pollution, checked November 13, 2026). The ordinance is Article VI of Chapter 58 of the county code.
The county's only numeric chlorine figure on that page is for pool water drained to a lawn, at 0.01 mg/L of chlorine or less. No figure covers house wash water, and a soft wash rinse is not stormwater, so the discharge rule applies to it in full. The crew plugs or covers the inlets downhill of the house before the first spray and keeps rinse water on the lot. The rule for commercial wash water, where volumes justify recovery equipment, is covered in commercial soft washing.
Pricing inputs for a residential soft wash
A residential soft wash price is built from seven inputs, each of which can be measured or looked up:
- Area: siding area from the perimeter times the wall height, plus gable triangles; roof area from the plan area including overhangs, times the pitch factor, which is 1.118 for a 6-in-12 roof.
- Mix and coverage: the strength for each surface and the gallons of mix per square foot, from the crew's own records.
- Concentrate: ProActive Solutions ProChlor 125, a 12.5% sodium hypochlorite product, is listed at $64.30 for a 5-gallon pail, or $12.86 a gallon (DFA Farm Supplies, ProChlor 125, checked November 13, 2026). The listing describes an EPA-registered sanitizer for food processing plants; the label of whatever product is bought governs its uses.
- Labor: the May 2025 median wage in services to buildings and dwellings was $17.21 an hour (BLS Occupational Outlook Handbook, last modified August 27, 2026), and wages were 74.6% of compensation in that industry group in June 2026 (BLS, Employer Costs for Employee Compensation, Table 4), a loaded rate of $23.07.
- Travel: 76 cents a mile from July 1, 2026 (IRS, standard mileage rates), plus drive time at the loaded rate.
- Equipment wear and consumables: pump, hose and reel wear, surfactant, plant covers and drain plugs.
- Tax: Florida does not tax pressure cleaning the exterior of a building or residential cleaning, but the cleaner pays sales tax and the county surtax on the supplies and equipment it uses (Florida Department of Revenue, GT-800015, rev. September 2015); the state rate is 6% (Florida Department of Revenue, sales and use tax).
A pressure washing business plan template collects the same inputs at the level of a year, where the crew's hours, the trailer and the chemical budget are planned together.
Sample job: a single-story vinyl ranch with a shingle roof in Pinellas County
The sample is hypothetical: a single-story house with a 34-by-50-foot footprint, 9-foot walls of vinyl siding, two gable ends and a 6-in-12 asphalt shingle roof with 1-foot overhangs. That is 1,801 square feet of siding and 2,093 square feet of roof. A crew of two spends 4.5 hours on site and 45 minutes each way driving 30 miles round trip. Coverage of 1 gallon of mix per 100 square feet on siding and 1 gallon per 50 square feet on the roof, the 3 percent roof strength, the hours, the consumables and the price are sample inputs. The roof strength is a sample because none of the three roof documents publishes one.
| Line | Calculation | Amount |
|---|---|---|
| Siding concentrate | 18.01 gal of mix × 1.25 ÷ 12.5 = 1.801 gal × $12.86 plus 6% state tax | $24.55 |
| Roof concentrate | 41.86 gal of mix × 3 ÷ 12.5 = 10.046 gal × $12.86 plus 6% state tax | $136.95 |
| Surfactant, compatible with sodium hypochlorite | Sample | $9.00 |
| Plant covers and drain plugs | Sample | $6.00 |
| Labor on site | 2 workers × 4.5 h × $23.07 | $207.63 |
| Drive time | 2 workers × 0.75 h × $23.07 | $34.61 |
| Mileage | 30 miles × $0.76 | $22.80 |
| Pump, hose and reel wear | Sample | $35.00 |
| Direct cost | Sum | $476.54 |
| Price | Sample | $725.00 |
| Gross profit | $725.00 − $476.54 | $248.46 |
| Gross margin | $248.46 ÷ $725.00 | 34.27% |
The roof is 84.8% of the chemical cost, so the roof strength is the input that moves the price. At 1.25 percent on the roof, the roof concentrate falls from $136.95 to $57.06; at 2 percent, to $91.30. Labor and drive time are 50.83% of direct cost and chemicals 33.89%, against a siding-only wash where labor dominates. No sales tax is added to the invoice, since Florida does not tax the service; the tax sits inside the supply lines. The county surtax on supplies is left out of the sample and adds to each supply line at the county's rate.
Residential soft washing checklist
- Record the siding material and the shingle maker on the estimate for every house.
- Read the siding maker's and the shingle maker's cleaning instructions, and note any strength ceiling or ban on chlorine or brushing.
- Keep the SDS for each chemical bought on the job record, and confirm the surfactant's compatibility with sodium hypochlorite in writing.
- Test the concentrate's strength before mixing, and mix each surface at the lowest strength its maker allows.
- Walk the plantings with the homeowner; pre-wet, cover, rinse and photograph them.
- Plug or cover the storm inlets downhill of the house before the first spray, and keep rinse water on the lot.
- Wear goggles, chemical-resistant gloves and an apron while pouring concentrate, with an eye wash on the rig.
- Price from measured areas, mix strengths, concentrate cost with tax, loaded labor and travel.
- Verify: photograph the siding, roof and plantings before and after, and record the strengths, drain covers and rinses on the work order before the invoice is sent.
Estimates, job photos and checklists in FieldRanger
The checklist ends in records, and FieldRanger keeps them on the job. An estimate is built from the HubSpot deal or contact record without leaving HubSpot, or in FieldRanger and kept tied to the deal, and a won HubSpot deal becomes a job with its context carried over. The job is assigned to a technician, and the work order on the assigned technician's phone carries the job details and instructions, such as the shingle maker and the mix strengths. Custom checklists hold the plant and drain steps, and before and after photos are attached to the work order and sync to the customer's HubSpot record.
Recurring job templates hold the annual or twice-yearly rewash. The invoice is generated from the completed work order, and payment can be taken in the field through Stripe. FieldRanger has no weather feed, so a wash postponed for rain or wind is moved by dragging the job on the calendar rather than by a forecast rule. The job photos page covers the photo record; plans, and Start free trial for 14 days with no card, are on pricing.
Frequently asked questions
What is residential soft washing?
It is cleaning a home's siding and roof with diluted sodium hypochlorite applied at low pressure, left to dwell and rinsed, so chemistry removes algae, mildew and dirt instead of water force.
What mix strength is used for soft washing vinyl siding?
CertainTeed's vinyl siding recipe works out to 1.25 percent sodium hypochlorite, and its page warns that greater concentrations may damage the siding. From 12.5 percent concentrate, that is 1 gallon of concentrate in a 10-gallon batch.
Can roof algae streaks be soft washed with bleach?
The ARMA bulletin describes household bleach and water, while Atlas Roofing recommends oxygen bleach and warns against chlorine, and CertainTeed names no chemical. All three rule out a pressure washer, so the shingle maker's own instructions decide the method.
How are plants protected during a house soft wash?
The crew wets plants before spraying, covers low plants beside the wall, applies the mix at the lowest strength the surface maker allows, rinses the plants after each section and before leaving, and photographs them before and after.
Is residential soft washing taxable in Florida?
Florida does not tax pressure cleaning the exterior of a building or residential cleaning, according to the Department of Revenue's cleaning services guide. The washing company still pays sales tax on the chemicals and equipment it buys.
On the Pinellas County ranch, the 1,801 square feet of siding needs $24.55 of concentrate and the 2,093 square feet of roof needs $136.95, a gap set by a 3 percent strength that no shingle maker in the table publishes; the price of a residential soft wash moves with the roof line on the estimate, and that line starts from the shingle maker's name.
Run field service on HubSpot with FieldRanger
Estimates with e-signature, scheduling and dispatch, a technician mobile app and invoicing, synced to the HubSpot deals and contacts the business already keeps.
Book a demo