Template

Field Service Report Template:Readings, Parts, Photos and Sign-Off for a Standby Generator Service

Field service report template with work performed, readings, parts, photos, recommendations and signatures, filled for a generator service in West Virginia.

Updated 11 min read

Download .xlsxExcel spreadsheet · 18 KB · Free, no sign-upFill it in online

A field service report template is the technician's record of a finished visit: the site and equipment, the work performed, the readings taken, the parts used, the photos, the recommendations for further work, and the signatures of the technician and the customer's representative. The example below fills every field for an annual service on a 150 kW standby diesel generator.

The field list is free and ungated, one of the free field service templates kept by FieldRanger, which makes field service software that runs inside HubSpot. A work order is written before the visit and says what to do. The field service report is written at the end and says what was found and done.

Field service report fields from arrival to sign-off

The table lists the template's fields, and the free .xlsx download, with no sign-up, carries them on a Template sheet. On that sheet each field takes one row. In Word or on paper it becomes a one- or two-page form with ruled space for findings.

Field service report template fields and what goes in each
SectionFieldWhat goes in it
HeaderService companyBusiness name, address, telephone, and any license or certification number the trade requires
HeaderReport number and dateA unique number, the visit date, and the work order or job number the visit closes
HeaderCustomer and siteCustomer name, site address, building or room, and the contact on site
EquipmentEquipment identificationMake, model, serial number, rating, install year and the customer's asset tag
EquipmentService typeScheduled maintenance, repair, inspection, emergency call or warranty work
VisitTechnician and timesTechnician name, arrival and departure times, and hours on site
VisitReason for visitThe request or schedule item that set up the visit, copied from the work order
ConditionAs-found conditionWhat the technician found before touching anything, including alarms and codes displayed
WorkWork performedEach task done, in order, with the procedure or checklist item it followed
ReadingsMeasurementsEach reading with its unit, the step at which it was taken, and the acceptable range where one exists
PartsParts and materialsPart description, quantity, and whether it came from van stock, a warehouse or the customer
Test equipmentInstruments and loaned equipmentMeters, gauges and test sets used, such as a load bank, with asset numbers
PhotosPhoto logPhoto number, subject, and whether it was taken before or after the work
ResultsAs-left conditionIn service, in service with a deficiency, or out of service
RecommendationsFollow-up workDeficiencies not corrected on the visit, their priority, and the quote or work order that covers them
RecordsCompliance entriesEntries a rule, a warranty or an insurer requires, such as run hours or refrigerant added
Next serviceNext dueThe date or meter reading at which the next service falls due
Sign-offSignaturesTechnician signature, and the name, title and signature of the customer's representative, with the time signed

Filled field service report: annual service on a 150 kW standby generator in Charleston, West Virginia

The visit is the annual service on a diesel standby generator at a three-story medical office building. The engine was installed in 2004. The business, customer, readings and part counts are illustrative; the maintenance intervals and record entries follow the federal rule set out in the next section.

Filled field service report, header, equipment and visit (example business, illustrative entries)
FieldExample entry
Service companyExample Power Systems LLC, 400 Example Street, Charleston, WV 25301 · 304-555-0147
Report number and dateFSR-2026-0912 · November 10, 2026 · closes work order WO-2026-1488
Customer and siteExample Medical Properties LLC, 1500 Example Boulevard, Charleston, WV 25311 · generator pad, north lot · contact: R. Okafor, facilities manager
Equipment identification150 kW diesel standby generator set, 480 V three-phase · engine serial 00000000 (example) · installed 2004 · asset tag GEN-01 · automatic transfer switch ATS-01, 400 A
Service typeScheduled annual maintenance with a load bank test, under the service agreement
Technician and timesD. Varga · arrived 8:05 AM, left 12:41 PM · 4.6 hours on site
Reason for visitAnnual service, recurring job GEN-ANNUAL · previous oil and filter change November 14, 2025, at 612.0 hours
As-found conditionController in Auto, no active alarms · block heater on · surface cracks on the lower radiator hose at the engine clamp · fuel tank 82% full, sample clear
Instruments and loaned equipmentResistive load bank, asset LB-04 · digital multimeter · coolant refractometer
As-left conditionIn service, controller in Auto, output breaker closed
SignaturesD. Varga, 12:38 PM · R. Okafor, facilities manager, 12:40 PM
Filled field service report, readings by test step (illustrative values)
StepReadingValue
ArrivalHour meter, non-resettable646.2 h
ArrivalBattery resting voltage · charger float voltage12.7 V · 13.5 V
ArrivalCoolant freeze point by refractometer · jacket water temperature on the block heater−34°F · 104°F
Start, no loadCranking voltage · time to rated speed10.9 V · 4 s
No load, 15 minutesOil pressure · coolant temperature · frequency58 psi · 182°F · 60.0 Hz
No load, 15 minutesOutput voltage A-B, B-C, C-A481 V, 479 V, 480 V
Load bank at 50%, 30 minutesLoad · frequency · oil pressure75 kW · 59.9 Hz · 56 psi
Load bank at 75%, 60 minutesLoad · current per phase · voltage · coolant temperature · exhaust temperature112.5 kW · 136 A · 478 V · 190°F · 720°F
Transfer testUtility-to-generator transfer time · retransfer delay setting8 s · 5 min
DepartureHour meter · run time this visit648.2 h · 2.0 h
Filled field service report, work, parts, photos and recommendations (illustrative entries)
FieldExample entry
Work performed1. Inspected belts, hoses, wiring, exhaust and enclosure · 2. Ran the load bank test above · 3. Changed oil and filter hot, after the test · 4. Inspected and replaced the air filter element · 5. Replaced both fuel filters and bled the fuel system · 6. Replaced the lower radiator hose · 7. Tested the transfer switch on a simulated utility failure · 8. Returned the controller to Auto
Parts and materialsOil filter, 1 · air filter element, 1 · fuel filters, 2 · lower radiator hose with 2 clamps · 15W-40 engine oil, 9 gal · 50/50 coolant, 1 gal top-off · all checked out of the Charleston warehouse onto van 3
Photo logP1 hour meter at arrival · P2 cracked hose, before · P3 new hose, after · P4 load bank display at 75% · P5 battery date codes · P6 fuel sample jar
Follow-up workPriority 2: batteries dated March 2021; cranking voltage passed at 10.9 V; replacement quoted on Q-2026-0377 for before the first freeze · Priority 3: exhaust rain cap sticks half open; added to the same quote
Compliance entriesOil and filter changed at 648.2 h · air cleaner inspected and replaced · hoses and belts inspected, one hose replaced · 2026 hours to date: 6.0 emergency (utility outage, July 18, 2026) and 26.5 maintenance and testing, this visit included · load bank test recommended in the manufacturer's maintenance schedule
Next dueOil and filter, hoses and belts: 1,148.2 h or December 10, 2027, whichever comes first · air cleaner: 1,648.2 h or December 10, 2027

The run time reconciles with the meter: 648.2 less 646.2 is the 2.0 hours of warm-up, load steps and cool-down. At 75 percent load, 112,500 W divided by the square root of 3 times 478 V gives about 136 A per phase.

Generator maintenance records under the federal RICE rule

The compliance row is required for this engine. The federal air rule for stationary reciprocating internal combustion engines (RICE) is 40 CFR part 63 subpart ZZZZ. At an area source of hazardous air pollutants, it treats an engine as existing if its construction began before June 12, 2006 (40 CFR 63.6590, Cornell LII, checked November 2026). The 2004 engine in the example is existing. A newer engine at an area source meets the rule through the federal engine standard in 40 CFR part 60 subpart IIII instead, and the intervals below do not apply to it.

Table 2d intervals for an existing emergency compression ignition engine at an area source
ItemInterval, whichever comes first
Oil and filterChange every 500 hours of operation or within 1 year + 30 days of the previous change
Air cleanerInspect every 1,000 hours or within 1 year + 30 days of the previous inspection; replace as necessary
Hoses and beltsInspect all of them every 500 hours or within 1 year + 30 days of the previous inspection; replace as necessary

The intervals are quoted from Table 2d to subpart ZZZZ (Cornell LII), checked November 2026. An oil analysis program may extend the oil interval. Under it, the oil is condemned when its Total Base Number falls below 30 percent of new, its viscosity changes by more than 20 percent, or its water content exceeds 0.5 percent by volume (40 CFR 63.6625).

Two more rules set the readings table. The engine needs a non-resettable hour meter (40 CFR 63.6625(f)). The owner keeps records of the hours it shows, split into emergency and non-emergency operation with the reason for each emergency run, and records of the maintenance itself (40 CFR 63.6655). Maintenance checks and readiness testing may run up to 100 hours in a calendar year, counted with other non-emergency hours, where the manufacturer, the vendor, a government body or the insurer recommends them. Emergency operation has no time limit (40 CFR 63.6640).

The report is where those records start. The two meter readings give the 2.0 hours of testing, the July outage is logged as emergency hours with its reason, and the next-due row comes from both the meter and the calendar. After this visit, GEN-01 has used 26.5 of its 100 testing hours for 2026.

Field service report instructions in visit order

  1. Before the visit, copy the work order number, the equipment identification and the reason for the visit into the header.
  2. On arrival, record the time and the as-found condition before touching the equipment, and photograph the hour meter.
  3. Record each reading at its test step, with its unit, so next year's visit can compare like with like.
  4. Record each task and each part as it is done, with the part's quantity and source.
  5. Number the photos in the log, so the work and the recommendations can refer to them.
  6. Record the as-left condition, and write each deficiency left uncorrected as a recommendation with a priority and a quote number.
  7. Fill the compliance entries and compute the next due date and meter reading, then collect both signatures and the time.
  8. Before sending, check that the departure meter less the arrival meter equals the run time, that every part appears in the work performed, and that every recommendation carries a reference number.

Field service report, work order and service invoice

Three documents cover one visit. The work order authorizes the job, and the work order template lists its fields. The field service report records what was found, measured and done, for the customer and the equipment's file. The invoice bills for the visit from the hours and parts the report recorded.

The report varies with the work. The same template, used as a technical service report template, suits the engineering report written after a diagnosis, where the findings carry test data and analysis. The generator report sits between them: a scheduled visit whose readings are compared year to year.

Work order software and the signed service report

A paper report reaches the office when the technician does, and its recommendations wait there until someone retypes them into a quote.

In FieldRanger, the field service report is the completed work order, on the technician's phone in a mobile app built for technicians in the field. A job-specific checklist carries the inspection items the RICE rule names. Before and after photos attach to the work order, and the customer signs on site as proof of completion. Time is logged against the job at clock-in and clock-out, parts are checked out of a specific warehouse and logged to the job, and the load bank is checked out by scanning its QR code.

Job completions, notes and updates are logged to the HubSpot timeline, photos sync to the customer's HubSpot record, and job status shows on the deal. A recurring job template sets up next year's visit, and the invoice is generated from the completed work order. The work order software page lists the fields a FieldRanger work order carries.

The technician enters the meter readings on the job checklist, and the yearly hour tally stays in the owner's records.

Fill it in here, or download the spreadsheet

The form below is the same template: totals calculate as you type, with the spreadsheet's own formulas, and your entries stay in this browser. Download it filled in, print it or save it as a PDF, or take the blank file.

Frequently asked questions

What should a field service report include?

The site and equipment, the technician and times, the as-found condition, work performed, readings with units, parts, a photo log, the as-left condition, recommendations, compliance entries, the next due date and both signatures.

What is the difference between a field service report and a work order?

A work order is written before the visit and authorizes the job. A field service report is written at the end of the visit and records what the technician found, measured, replaced and recommended, signed by the customer's representative.

Is there a field service report template download for Excel or Word?

Yes, for Excel. The page offers a free .xlsx download with no sign-up: a Template sheet with one row per field and a Sample sheet with the filled report. A one-page Word form can follow the same fields.

What does a field service report form need for generator service?

Hour meter readings at arrival and departure, battery and charger voltages, oil pressure, coolant temperature, frequency and voltage at no load and under load, transfer switch timing, and the run hours split into emergency and non-emergency use.

What maintenance records does EPA require for an emergency diesel generator?

For an existing emergency diesel engine at an area source, 40 CFR part 63 subpart ZZZZ requires a non-resettable hour meter, hour records split into emergency and non-emergency operation, and records of the maintenance done.

Who signs a field service report?

The technician, and the customer's representative on site, with name, title and time. The signature acknowledges the visit and its recommendations; it does not accept the follow-up quote.

Generator GEN-01 after report FSR-2026-0912

GEN-01 leaves the November visit with a battery quote open and its next oil change due at 1,148.2 hours or on December 10, 2027. Next November's report starts from this one, with the same readings at the same steps compared line by line. The maintenance work order template schedules that visit; a demo shows the same fields as a FieldRanger work order on a phone, and Start free trial on pricing opens 14 days with no card.

FieldRanger runs field service inside HubSpot

Estimates, scheduling and dispatch, a technician app and invoicing on the HubSpot records sales already keeps. Every plan starts with a free trial.

Book a demo