Template

HVAC Service Report Template:Superheat, Subcooling, Static Pressure and Amperage Readings, an EPA 608 Refrigerant Record and Sign-Off for an Augusta, Georgia Repair

HVAC service report template with superheat, subcooling, static pressure and amperage readings, an EPA refrigerant record and sign-off, filled for Augusta, GA.

Updated 13 min read

Download .xlsxExcel spreadsheet · 18 KB · Free, no sign-upFill it in online

An HVAC service report template sets out what a technician records on a repair call: the complaint, the equipment's data plate figures, readings before and after repair (superheat, subcooling, static pressure, amperage, temperature split), the diagnosis, work and parts, an EPA Section 608 refrigerant record, recommendations and both signatures. The example below fills a no-cool call in Augusta, Georgia.

FieldRanger lists it with its free field service templates; FieldRanger is the HVAC software that runs inside HubSpot. A service report records a diagnosis and a repair. A maintenance checklist records a seasonal tune-up, and the two carry different rows.

HVAC service report fields for a repair call

The fields below are the report form. In Word or Google Docs it becomes two pages; in a spreadsheet the readings block becomes a grid with a before and an after column.

HVAC service report template fields and what goes in each
SectionFieldWhat goes in it
HeaderCompany and licenseBusiness name, phone and the state contractor license number
HeaderReport number and callReport number, date, and the call or work order the visit closes
HeaderCustomer and siteName, service address and the contact on site
EquipmentOutdoor unitMake, model, serial, install year, tonnage, refrigerant type, factory charge and line set adjustment
EquipmentIndoor unitFurnace or air handler make, model, serial, and the maximum external static pressure on its rating plate
EquipmentData plate electricalCompressor rated load amps (RLA), fan and blower full load amps (FLA), and the voltage rating
EquipmentMetering device and charge targetTXV or fixed orifice, and the manufacturer's subcooling or superheat target
VisitTechnicianName, EPA Section 608 certification type and certificate number
VisitTimesArrival, departure and hours on site
ComplaintReported problemThe customer's words, unedited
ConditionsTest conditionsOutdoor dry-bulb, return dry-bulb and wet-bulb, and minutes of run time before readings
ReadingsLow sideSuction pressure, evaporator saturation temperature, suction line temperature, superheat
ReadingsHigh sideLiquid pressure, condenser saturation temperature, liquid line temperature, subcooling
ReadingsCharge resultMeasured value minus target, and pass or fail against the tolerance used
ReadingsStatic pressureReturn and supply external static, total external static, and the rated maximum
ReadingsAirflowCFM from the blower table at the measured static and fan speed, against design airflow
ReadingsElectricalVoltage at the disconnect; amperage on the compressor, condenser fan and blower against the data plate
ReadingsTemperature splitReturn and supply air temperatures and the difference
DiagnosisCause foundWhat failed, where, and how it was confirmed
WorkWork performedEach step in order
PartsParts and materialsPart, quantity and source
RefrigerantRefrigerant recordType, amount recovered and its cylinder, evacuation level verified, amount added, leak location and repair, and the rule notes below
ResultsReadings after repairThe full readings block repeated after the repair
RecommendationsFollow-up workProblems not fixed on the visit, priority and quote number
Sign-offSignaturesTechnician signature, and the customer's printed name, signature and time

Readings block: superheat, subcooling, static pressure and amperage

Each reading on the report is a measurement compared with a reference from the equipment's own paperwork. The report is useful only if it carries both, plus the conditions under which the measurement was taken.

HVAC service report readings, how each is computed and what it is compared with
ReadingHow it is computedReference
SuperheatSuction line temperature minus evaporator saturation temperatureManufacturer's superheat table at the day's outdoor dry-bulb and return wet-bulb, for a fixed orifice
SubcoolingCondenser saturation temperature minus liquid line temperatureManufacturer's subcooling target for a TXV system, from the data plate or installation instructions
Total external static pressureReturn static plus supply static, each entered as a positive valueMaximum external static on the furnace or air handler rating plate
AirflowRead from the blower table at the measured total static and the fan speed settingDesign airflow for the system
AmperageClamp meter on each motor lead while runningRLA for the compressor; FLA for fan and blower motors
Temperature splitReturn air temperature minus supply air temperatureNo fixed figure; meaningful only once airflow is known

ENERGY STAR's functional testing checklist sets a testing method that a service report can borrow. It requires 15 minutes of running before testing and records outdoor dry-bulb and return wet-bulb with the pressures and line temperatures. A TXV system passes when subcooling is within 3°F of the manufacturer's goal; a fixed-orifice system passes when superheat is within 5°F. It adds total external static from test holes in the return and supply, and airflow within 15 percent of design (ENERGY STAR MFNC HVAC Functional Testing Checklist, Rev. 05, revised January 15, 2025). The definition of each refrigerant reading is in what is superheat.

Refrigerant record under 40 CFR 82.156 and 82.157

Three federal rules decide what the refrigerant section must hold, and each applies to a different situation.

Before opening an appliance, technicians "must evacuate the refrigerant, including all the liquid refrigerant, to the levels in Table 1," using recovery equipment certified under 82.158, and "must verify that the applicable level of evacuation has been reached" before it is opened (40 CFR 82.156(a), Cornell LII, checked November 2026). Table 1 sets 0 inches of mercury vacuum for a high-pressure appliance with a full charge under 200 pounds, with recovery equipment of either age. A residential R-410A split system falls in that row, so the report records the gauge reading reached before the system was cut.

Disposal has its own record. Since January 1, 2018, technicians evacuating appliances with a full charge "of more than 5 and less than 50 pounds" for disposal keep three years of records under 82.156(a)(3):

  • the company name, location of the appliance, date of recovery and type of refrigerant recovered, for each appliance;
  • the total recovered from disposed appliances in each calendar month, by type;
  • the quantity transferred for reclamation or destruction, the person it went to, and the date.

A changeout that removes an old condenser fills this block; a repair does not.

The leak repair section, 40 CFR 82.157, applies as of April 10, 2020 only to appliances with a full charge of 50 or more pounds of class I or class II refrigerant, such as R-22. For those, the owner "must calculate the leak rate every time refrigerant is added," comfort cooling triggers repair at a 10 percent leak rate, and a technician who adds or removes refrigerant gives the owner a record of the amount and type. Records are kept for at least three years. For HFC systems, EPA's 2026 leak repair rule under the AIM Act excludes appliances in the residential and light commercial air conditioning and heat pump subsector (EPA, Leak Repair Requirements fact sheet, January 2026).

Opening the circuit takes an EPA certificate. Type II certification covers "servicing or disposing of high- or very high-pressure appliances," and an apprentice is exempt while "closely and continually supervised by a certified technician" (EPA, Section 608 Technician Certification Requirements, last updated July 15, 2026).

Filled HVAC service report: no-cool call on a split system in Augusta, Georgia

The call is a 3-ton split air conditioner with a gas furnace in a two-story house, running constantly without cooling the upstairs. The business, customer, data plate figures and readings are samples; the rule notes follow the section above.

Filled HVAC service report, header, equipment and complaint (sample entries)
FieldSample entry
Company and licenseExample Garden City Heating & Air LLC, Augusta, GA 30901 · 706-555-0162 · state license 000000 (example)
Report number and callHSR-2026-0915-03 · September 15, 2026 · closes call C-2026-2231
Customer and siteDenise Harper, 3125 Example Lane, Augusta, GA 30909 · home, 706-555-0175
Outdoor unit3-ton condenser, installed 2017, serial 0000000000 (example) · R-410A · factory charge 8 lb 2 oz for 15 ft of line set, plus 0.6 oz per foot beyond 15 ft
Indoor unitGas furnace with multi-speed blower and cased coil · rating plate maximum external static 0.50 in. w.c.
Data plate electricalCompressor RLA 14.1 A · condenser fan FLA 1.0 A · blower FLA 7.0 A · 208/230 V
Metering device and charge targetTXV · subcooling target 10°F
TechnicianTyrone Bell, EPA 608 Type II, certificate 000000 (example)
TimesArrived 1:05 PM, left 4:50 PM · 3.75 hours
Reported problem"Upstairs won't get below 80 and the outside unit never shuts off."
Filled HVAC service report, readings before and after the repair (sample readings)
ReadingBefore, 1:30 PMAfter, 4:20 PM
Test conditionsOutdoor 88°F DB · return 78°F DB, 64°F WB · 20 minutes runningOutdoor 90°F DB · return 77°F DB, 63°F WB · 15 minutes running after charging
Low side97 psig, 30°F saturation · suction line 58°F · superheat 28°F118 psig, 40°F saturation · suction line 49°F · superheat 9°F
High side295 psig, 95°F saturation · liquid line 93°F · subcooling 2°F340 psig, 105°F saturation · liquid line 95°F · subcooling 10°F
Charge resultSubcooling 8°F below target: failOn target: pass
Static pressureReturn 0.24, supply 0.36 · total 0.60 in. w.c. against 0.50 ratedReturn 0.20, supply 0.34 · total 0.54 in. w.c. against 0.50 rated
Airflow1,040 CFM from the blower table at 0.60 in., medium-high speed · design 1,200 CFM1,100 CFM at 0.54 in. · 8% below design
Electrical238 V · compressor 10.2 A · condenser fan 0.9 A · blower 5.8 A237 V · compressor 12.6 A · condenser fan 0.9 A · blower 5.6 A
Temperature splitReturn 78°F, supply 64°F · 14°FReturn 77°F, supply 57°F · 20°F
Filled HVAC service report, diagnosis, work, refrigerant record and sign-off (sample entries)
FieldSample entry
Cause foundUndercharge from a leak: electronic detector alarm at the condenser, confirmed with bubble solution at the outlet braze joint of the liquid line filter-drier · P1, P2
Work performed1. Recovered the charge to 0 in. Hg, verified on the gauge at 2:02 PM · 2. Cut out the filter-drier; brazed a new one with nitrogen flowing · 3. Pressure tested with dry nitrogen, 30-minute standing test, no drop · 4. Evacuated to 450 microns; isolated 10 minutes, rose to 620 microns and held · 5. Weighed in the full charge · 6. Replaced the dirty 1-in. filter · 7. Ran 15 minutes and took the after readings
Parts and materialsLiquid line filter-drier, 1 · 16 x 25 x 1 MERV 8 filter, 1 · brazing rod and nitrogen from van stock · R-410A, 8 lb 14 oz, new
Refrigerant recordR-410A · appliance full charge 8 lb 14 oz (8 lb 2 oz plus 20 ft at 0.6 oz) · evacuation to 0 in. Hg verified before opening, recovery machine RM-3 (certified under 82.158, example) · 6 lb 10 oz recovered to cylinder RC-14, sent for reclamation with the month's cylinders · 8 lb 14 oz added by weight · leak at the filter-drier outlet joint, repaired · leak rate calculation: not applicable, HFC and under 50 lb · disposal record: not applicable, appliance kept in service
Follow-up workPriority 2: total external static still 0.54 in. w.c. with a clean filter, above the furnace's 0.50 rating; return duct evaluation quoted on Q-2026-0721
SignaturesTyrone Bell, 4:45 PM · Denise Harper, 4:48 PM

The charge arithmetic closes. The appliance's full charge is 8 lb 2 oz plus 20 feet of extra line at 0.6 oz, which is 12 oz, giving 8 lb 14 oz. Recovery took out 6 lb 10 oz, so 2 lb 4 oz had leaked, about a quarter of the charge: consistent with a superheat of 28°F and a subcooling of 2°F on a TXV system. After the repair, subcooling sits on its 10°F target, inside the 3°F band, and the compressor draws 12.6 A against an RLA of 14.1 A.

The static pressure row is the finding the repair did not fix. A clean filter lowered total static from 0.60 to 0.54 in. w.c., but the reading still exceeds the furnace's rating, so the airflow stays 8 percent short and the report hands the problem to a quote rather than calling the call closed.

Report entries in visit order

  1. Copy the equipment, data plate figures and charge target into the header before the first reading, so every reading has its reference beside it.
  2. Write down what the customer reported, verbatim, then the test conditions and minutes of run time.
  3. Take the full readings block before touching the system: low side, high side, static, airflow, electrical and split.
  4. Write the diagnosis with the evidence that confirmed it, and photograph the fault.
  5. Before opening the circuit, record the evacuation level reached and the recovery cylinder; record every pound and ounce recovered and added.
  6. After the repair and 15 minutes of running, take the full readings block again in the after column.
  7. Give every problem the repair did not fix its own line: priority, recommended work, quote number.
  8. Before the customer signs, check that the added charge matches the computed full charge, that each reading has a reference beside it, and that the refrigerant record states which rule notes apply.

Service report, maintenance checklist, agreement and invoice

Four HVAC documents divide one customer's year. The HVAC maintenance checklist records the planned spring and fall visits; the service report records the unplanned call between them. The HVAC service agreement template sets which visits are covered and any discount on repairs. The HVAC invoice template bills the repair from the hours, parts and refrigerant the report recorded. The general field service report, written for any trade, has no refrigerant record and no charge target; the HVAC report exists to carry them.

FieldRanger and the readings on the work order

A paper report goes to a file cabinet, and the next technician at the Harper house starts without the 0.54 in. static reading or the open duct quote.

FieldRanger keeps this report as the closed job: a digital work order puts the job details, customer information and instructions on the technician's phone, and custom checklists hold the readings block and the refrigerant record. Photo documentation attaches the leak photos to the work order, photos taken on the job sync to the customer's HubSpot record, and the customer signs on site. Job completions, notes and updates are logged to the HubSpot timeline, the invoice is generated from the completed work order, and the duct quote can be built as an estimate from the HubSpot deal or contact record. The work order software page details the FieldRanger work order behind this report.

Readings reach FieldRanger as numbers the technician enters on the checklist. The monthly recovered-refrigerant totals that the disposal rule asks for are kept in the company's cylinder records.

Fill it in here, or download the spreadsheet

The form below is the same template: totals calculate as you type, with the spreadsheet's own formulas, and your entries stay in this browser. Download it filled in, print it or save it as a PDF, or take the blank file.

Frequently asked questions

What should an HVAC service report include?

The equipment and its data plate figures, the technician's EPA 608 certification, the complaint, test conditions, readings before and after the repair, the diagnosis, work and parts, a refrigerant record, recommendations with quote numbers, and the technician's and customer's signatures.

What readings go on an HVAC service report?

Suction and liquid pressures with saturation temperatures, suction and liquid line temperatures, superheat and subcooling against the manufacturer's target, return and supply static with the total, airflow from the blower table, voltage, motor amps compared with the RLA and FLA ratings, and the temperature split.

What refrigerant records does the EPA require from an HVAC technician?

Before opening an appliance the technician must evacuate to the Table 1 level in 40 CFR 82.156 and verify it. Disposal of an appliance holding more than 5 and less than 50 pounds requires records kept three years. Appliances with 50 pounds or more of R-22 or another ozone-depleting refrigerant also need leak rate calculations and a record of refrigerant added or removed.

Is there an HVAC service report template free download?

Yes. The page offers a free .xlsx download with no sign-up: a Template sheet with every field of the report, and a Sample sheet with the filled report and its readings before and after the repair.

How is total external static pressure measured on a service call?

With a manometer at test holes in the return and the supply, adding the two readings as positive values, then comparing the total with the maximum on the furnace or air handler rating plate.

What is the difference between an HVAC service report and an HVAC work order?

A work order sends the technician with the job details and the customer's request. The service report closes the call: it holds the measurements, the cause found, the repair, the recommendations and the customer's signature.

The Harper return duct after HSR-2026-0915-03

The September call left the system charged to 8 lb 14 oz, subcooling on its 10°F target and a 6 lb 10 oz cylinder entry waiting for the month's reclamation run. It also left a reading the repair could not move: 0.54 in. w.c. against a 0.50 rating, now quote Q-2026-0721. The fall maintenance visit on the same system will open with that number. The duct quote, the agreement and the invoice each have a form in the free field service templates hub. Per-technician plans for keeping these reports in FieldRanger appear at pricing, beside a 14-day Start free trial that takes no card.

FieldRanger runs field service inside HubSpot

Estimates, scheduling and dispatch, a technician app and invoicing on the HubSpot records sales already keeps. Every plan starts with a free trial.

Book a demo