Template

Free Plumbing Estimate Template:Every Field and a Filled Repipe and Water Heater Example

Plumbing estimate template with fixture, pipe, permit and water heater code lines, filled for a galvanized repipe and gas water heater in Golden Valley, MN.

Updated 10 min read

Download .xlsxExcel spreadsheet · 14 KB · Free, no sign-upFill it in online

A plumbing estimate template is the priced scope of plumbing work before it starts: each fixture connection, each run of pipe by size and material, the equipment, the code items the jurisdiction inspects, the permit, exclusions, the price and the terms. The example fills every field for a galvanized repipe and a gas water heater replacement in Golden Valley, Minnesota.

The field list is free and ungated, one of the free field service templates kept by FieldRanger, the plumbing software that runs inside HubSpot. An estimate prices work that has been scoped but not done. The bill that follows it is a different document, with hours and parts as used; the plumbing invoice template sets out its rows.

Plumbing estimate fields: fixtures, pipe, equipment, code items and permit

The table lists the template's fields, and the page offers them as a free .xlsx download with no sign-up. A plumbers estimate template in Word, Google Docs or a spreadsheet follows it row for row, with the fixture and pipe lines as a priced table.

Plumbing estimate template fields and what goes in each
FieldWhat goes in it
ContractorBusiness name, address, telephone, plumbing contractor license number and bond
Estimate number, date and expiryA unique number, the issue date and the date the price lapses
Customer and siteName, address, building type and age, and where the work is: basement, crawl space, walls
Existing systemPipe material and condition, water heater type, size and age, fuel and venting
Scope summaryOne sentence naming the work, so the lines below can be read against it
Pipe linesEach run by size, material and length: main, trunk, branches
Fixture linesEach fixture reconnected or replaced, with its stops and supplies
EquipmentWater heater or other appliance by type, capacity, fuel and model
Code itemsThe connections the jurisdiction inspects: gas valve, venting, relief valve discharge, combustion air
Access and removalWall or ceiling openings, old pipe removed or abandoned, disposal of old equipment
TestingThe pressure test and flush the new piping receives before it is closed in
PermitIssuing jurisdiction, permit types, fee basis, and the inspections scheduled
ExclusionsWork the price leaves out: wall patching and paint, the service line, concealed conditions
OptionsAlternatives priced outside the subtotal
Subtotal and taxThe sum of the lines and the tax treatment under the state's contractor rule
ScheduleDays on site and the period with the water off
WarrantyLabor warranty and the manufacturer's warranty on the water heater
Payment termsDeposit, balance due and methods
AcceptanceCustomer's signature, date and the options chosen

The code items row is what separates a plumbing estimate from a general estimate template. Each item is a connection the inspector looks at, so pricing it on its own line lets the customer see that it was included and lets the installer see what the inspection will check.

Filled plumbing estimate example: galvanized repipe and gas water heater in Golden Valley, Minnesota

A 1954 rambler has galvanized steel supply piping, low pressure at the upstairs fixtures and a 2009 gas water heater with a rusted tank seam. The basement ceiling is unfinished, so the trunk lines are exposed; the bathroom branches run in a plaster wall. The business, customers and prices are illustrative.

Filled plumbing estimate, header and terms (example business, illustrative entries)
FieldExample entry
ContractorExample Plumbing and Heating LLC, 5000 Example Road, Golden Valley, MN 55422 · 763-555-0119 · Minnesota plumbing contractor license PC000000 (example), bond on file
Estimate number, date and expiryPE-2026-0461 · November 12, 2026 · valid until December 31, 2026
Customer and siteAnn and Erik Lindgren, 1200 Sample Lane, Golden Valley, MN 55427 · one-story house with basement; water heater beside the masonry chimney
Existing systemGalvanized steel supply, 3/4 in main, 1/2 in branches · 40-gallon atmospheric gas water heater, 2009, vented to a clay-lined chimney
Scope summaryReplace the supply piping from the meter to every fixture with PEX-A and replace the water heater with a 50-gallon atmospheric gas unit
TestingNew piping pressure tested before walls are closed; system flushed
PermitCity of Golden Valley plumbing and gas permits; final inspection scheduled at least 24 hours ahead
ExclusionsPlaster patching and paint; the service line from the street to the meter; galvanized pipe left capped inside finished walls
ScheduleTwo days on site · water off from 8:00 AM to 4:00 PM on day one
WarrantyLabor 1 year · water heater under the manufacturer's tank and parts warranty
Payment terms$1,500.00 at acceptance; balance at final inspection · card, check or bank transfer
AcceptanceCustomers' signatures, date and the options chosen
Filled plumbing estimate, pipe, fixture, equipment and code lines (illustrative prices, installed)
LineQuantityUnit priceLine total
Main shutoff, 3/4 in full-port ball valve at the meter1$145.00$145.00
PEX-A, 3/4 in, main and trunk, with hangers85 ft$9.50$807.50
PEX-A, 1/2 in, branches to fixtures140 ft$7.25$1,015.00
Kitchen sink: two quarter-turn stops and supplies1$165.00$165.00
Bathroom lavatory: two stops and supplies1$150.00$150.00
Toilet: stop and supply1$85.00$85.00
Tub and shower valve: new supply connections1$240.00$240.00
Laundry: recessed washer outlet box with valves1$265.00$265.00
Frost-free sillcocks2$185.00$370.00
Remove exposed galvanized; cap concealed sections1 lot$350.00$350.00
Wall openings for the bathroom branches2$60.00$120.00
Water heater, 50-gallon atmospheric gas, EX-WH50 (example), installed1$1,950.00$1,950.00
Gas connection: shutoff valve in the same space, ground union, drip tee1$165.00$165.00
Vent connector to the chimney, with clearances and pitch1$210.00$210.00
Temperature and pressure relief discharge pipe, full size1$55.00$55.00
Remove and dispose of the old water heater1$95.00$95.00
Subtotal$6,187.50
City of Golden Valley plumbing and gas permits1at costbilled on the invoice
Option, outside the subtotal: pressure-balancing tub and shower valve in place of reconnection1add $425.00

The permit line carries no figure because the fee is the city's, not the contractor's, and it is passed through at the amount the city charges. Pressure testing and flushing appear in the terms rather than as lines: they are part of every pipe line's price.

Golden Valley water heater items behind the code lines

The code lines come from the city's water heater replacement handout, which states that the water heater "must be listed and labeled and installed in accordance with the manufacturer's installation instructions and the Minnesota State Plumbing Code" (City of Golden Valley Inspections, Water Heater Replacement, checked November 2026). Its items map onto the estimate line by line.

Golden Valley water heater replacement items and the estimate line each sets
Handout itemEstimate line
A listed and approved gas valve in the same space as the water heater; a ground union downstream of the shutoff on iron gas pipe; a drip tee on the water heater gas lineGas connection
Single-wall vent connector at least 6 inches from combustibles; Class B vent at least 1 inch; an approved chimney connection with at least 1/4-inch pitch up to the flueVent connector
Combustion air correctly sized, from outside, inside or both, with a worksheet when any air comes from insideExisting system row: chimney and room checked at the walk-through
A water shut-off valve on the cold water sideWater heater, installed
A full-size temperature and pressure valve discharging within 18 inches of the floorRelief discharge pipe
Access not through a bedroom, bathroom, toilet room or storage closet; removable without removing a permanent part of the structureCustomer and site row: location beside the chimney
Flue liner required for a transite chimney; oval transite not allowedExisting system row: clay-lined chimney recorded
Final inspection, scheduled at least 24 hours in advance with the permit numberPermit row

The Lindgren chimney is clay-lined, so no liner line appears. A transite chimney would add one, and an oval transite flue would change the venting line entirely; the existing system row records the chimney before the price is written.

Minnesota license, bond and tax rows

The contractor row carries a license and a bond because Minnesota requires both. No person may perform or offer to perform plumbing work without a contractor's license, and each person who does must maintain a bond of at least $25,000, with liability insurance of at least $50,000 per person and $100,000 per occurrence (Minnesota Statutes 326B.46, Office of the Revisor of Statutes, 2026 edition). The statute lets an unlicensed individual do plumbing work on that individual's own residence; a business working on the Lindgren house needs the license.

The tax row adds nothing. The Minnesota Department of Revenue tells contractors to pay sales or use tax on the materials they use and states "Do not charge sales tax on construction contracts"; it lists water heaters among repairs to real property and counts work on plumbing as improving real property (Minnesota Department of Revenue, Contractors and Other Property Installers Industry Guide, General Contractors and Subcontractors section updated June 18, 2024). The water heater and the PEX are taxed when the contractor buys them.

Plumbing estimate instructions from the walk-through to the signature

  1. Walk the system from the meter to the last fixture and record the pipe material, sizes and where each run is concealed.
  2. Record the water heater's type, capacity, fuel, age and venting, and look at the chimney liner and the combustion air.
  3. Measure each pipe run and price it by size and material, then price each fixture connection with its stops.
  4. Price the equipment, then one line for each code item the jurisdiction's handout names.
  5. Add access openings, removal and disposal, and state what is left in the walls.
  6. Name the permits, carry the fee at cost, and state the tax treatment under the state's contractor rule.
  7. State the exclusions, options, schedule, water-off period, warranty and payment terms.
  8. Before sending, read the scope summary against the lines: every fixture in the house appears once, and the lines add up to the subtotal.

Plumbing estimates, plumbing quotes and the invoice

A plumbing estimate prices a scope line by line, as above. A plumbing quote states a pricing method, flat rate or time and materials, and the figure it produces; the plumbing quote guide compares the two methods and prices a bathroom rough-in both ways. The Lindgren estimate also serves as a plumbing quote example: once accepted, its subtotal is the price, and only the permit fee and any option chosen are added. A plumber estimate template is the same document under the name a plumber searches for, and the invoice that closes this job follows the plumbing invoice template with the permit fee entered at cost.

Estimating software and the accepted plumbing estimate

On paper, an accepted repipe becomes three more documents: a parts order, two days on a calendar, and an invoice typed from the estimate with the permit fee added.

In FieldRanger, the estimate is built from the HubSpot deal or contact record without leaving HubSpot, or in FieldRanger and kept tied to the HubSpot deal it belongs to, and PandaDoc sends it for signature. The won deal becomes a job with its context carried over, and job status shows on the deal record. Technicians check the PEX, fittings and water heater out of a specific warehouse, so stock is counted where it sits. Time is logged against the job, and the invoice is generated from the completed work order. The estimating software page describes the estimate on the HubSpot deal.

Estimates are built from FieldRanger's price book of services, parts and rates, where the company keeps its PEX, fittings and labor rates. The handout items come from the jurisdiction and are entered when the estimate is built.

Fill it in here, or download the spreadsheet

The form below is the same template: totals calculate as you type, with the spreadsheet's own formulas, and your entries stay in this browser. Download it filled in, print it or save it as a PDF, or take the blank file.

Frequently asked questions

What should a plumbing estimate include?

The contractor's license, the customer and site, the existing system, a scope summary, pipe lines by size and material, fixture lines, equipment, code items, access and removal, testing, the permit, exclusions, options, tax treatment, schedule, warranty, payment terms and acceptance.

What does a plumbing quote example look like?

The Golden Valley estimate on this page is one: pipe and fixture lines priced as installed work, a water heater with its code items on separate lines, permits at cost and a pressure-balancing valve priced as an option.

Does replacing a water heater need a permit in Golden Valley, Minnesota?

The city lists its water heater handout among its building and remodeling permits, and the handout requires a final inspection scheduled with the permit number at least 24 hours ahead.

Do plumbers charge sales tax in Minnesota?

Not on construction contracts. The Minnesota Department of Revenue treats plumbing work and water heater replacement as improvements to real property: the plumber pays tax on materials when buying them and does not itemize sales tax on the customer's bill.

Is the plumbing estimate template free?

Yes. The page offers it as a free .xlsx download with no sign-up: a Template sheet with every field and the priced lines, and a Sample sheet with the filled Golden Valley estimate.

The Lindgren repipe at final inspection

Estimate PE-2026-0461 ends at the final inspection, where the inspector reads the gas valve, the vent connector and the relief discharge against the same handout the code lines came from. The Lindgrens' invoice then adds the one figure the estimate could not hold, the permit fee, and the plumbing invoice template and the other free field service templates carry the job from there. A two-day repipe fits inside the 14-day Start free trial, which needs no card; plans per technician are on pricing.

FieldRanger runs field service inside HubSpot

Estimates, scheduling and dispatch, a technician app and invoicing on the HubSpot records sales already keeps. Every plan starts with a free trial.

Book a demo